cylinder

Ouch!!! My C180 '97 run only with 2 and 3 cylinder. 1 and 4 not have Sparkling and injector not run. Help please. Have idea of disaster? Thanks

Hi any recommendations for Cylinder head and porting work guys ? Cheers Mike

So I have a W212 E200 CDI Auto with the following fault: Fault: The output for glow plug (cylinder 1) has an electrical fault or interruption. Questions: 1. Are the glow plugs the same as the E220/E250? 2. Any image / diagram to show where my one is located? 3. Is it easy to access /...

Hello everyone, I'm driving w203 c200, M111 engine. I had done several test but misfire on Cylinder 2 remain the same (no spray): 1. swap ignition coils. 2. swap fuel injectors. 3. wire harness have power and i'm using test light only. Faulty code : 1. P0302 - Cylinder 2 Misfire...

Moving on from John D's and contributors' helpful thread on cylinder locks (https://www.mbclub.co.uk/forums/general-discussion/222924-get-those-house-cylinder-locks-changed.html), I decided it was timely to review our side door security as the 15 year old handles were tatty and felt like they...

I've been dismantling my drivers door on my 2006 ML 320 CDI W164 to repair or replace the door actuator. I've read several guides on how to do this and this video explains the process of removing the actuator: https://www.youtube.com/channel/UCzLJe0r0Wur7YAsD_RlQC3w However, unlike in the...

In the last couple of weeks I've been made aware of car thefts via key thefts from property, including a neighbour, a cousin, and an E63 owner. All were stolen by crooks snapping the Eurocylinder locks on front/patio/rear doors, where the locks can be snapped in seconds, before entering the...

*0632 Misfire * 0648 Miafiring Of Cylinder 6 Worsening Of Exhaust Emission Value After Engine Start ( P0306) * 2326 The Engine Off Time has Has An Implausible Value Compression Test Done Cylinder 6 Side All Low Compression Other Side Is All Good Dont Know What To Do Any Suggestions Let Me Know

Late last year I bought my R129 - a nice clean 74000 mile 1992-registered 500SL - which is about to receive a stem-to-stern refresh - fluids, filters, bushes, shocks, steering, mounts, HT system, the lot. My roof is in good working order but I know I need to flush and replace my hydraulic...

Cylinder misfire on M120 engine (SL70) Hi all, There was some misfiring detected in 2 or 3 of the cylinders in my car. According to the dealer, it would require about 32 manhours to remove cylinder heads to check (so some £5,000). Other option is to run some miles on it to see if...

Hi all, really hoping that someone can help. My C230 threw a P2006 (Intake Manifold Runner Control Stuck Closed Bank 1) error code and after removing the Intake Manifold I discovered the whole unit needed replacing, so sadly the cheap fix went out the window. I also found that the MAP Sensor...

This a.m. was watching the F1 race when I noticed a slow drip coming from the ceiling light fixture. Investigated & the 1200 x 450, vented, indirect at least 20 y.o. hot water cylinder has a slowish drip leaking from the cold water intake. All looks a bit crusty & it seems it's been going on...

hello everyone i apologise in advance if this is not the correct forum to post this in but i cannot find anywhere else to post about this. w639 111 2.2cdi 2005 my clutch master cylinder recently started leaking and small amounts of brake fluid started dripping onto the floor, i have been...

Recently had a diagnostic test and this fault came up cylinder 2, took it to a local garage who advertise they work on MB cars, but they refused to change the plug stating they would need specialist equipment to remap ECU Is this correct because reading the forum's here people have changed...

Ported and polished cylinder heads for the supercharged 55 M113K engine. Covered 5K miles. Have been cleaned and pressure tested. Located in Milton Keynes. Price is £800 + your original heads.

Taken out 12x head bolts, the head is loose, and I can lift it 1/2 inch or so, but something is holding it at the rear. Seems like a thin steel tube is attached to the head (like a brake or fuel line) at the back, near the exhaust manifold. I need primarily to know how to remove it, and...

Hello there, has anyone got a cylinder head for a 124 , 200E, petrol , 4 cylinder, laying around ?

Anyone got a cylinder head for a 124 petrol 200E laying around ?

Greetings, Lately, my brake pedals been sporadically disappearing into the floor panel after a recent copper hose + fluid change. I thought about changing my master cylinder and called MB UK to order a replacement only to learn that they only stock ATE and no Bendix. I'm not sure what my...

anyone got one or know where to get one (other than ebay), is ebay trust worthy enough for such a thing???