Recent content by mhuk

  1. M

    Simple one. Fuel hose W210 OM606

    Hi Guydewdney, Not sure which plastic pipes you are taking about on bulk head. I have a w210 with om606. Looks like this... I replaced the two O rings you speak of. I now get no bubbles going into the fuel line. I should say right now that I broke off a clip. Look at the top picture and...
  2. M

    Simple one. Fuel hose W210 OM606

    It will not start. I can see a lot of air in the pipe number 2 I suspect the pre filter is letting air in. Total pain as the car is sat on the road now. :-( Performance wise it did seems a little slower.
  3. M

    Replacing fuel line into prefilter

    Hi, I changed the seala on those clear pipes this weekend just gone. It's not hard to remove the inlet but going back on is hard work. You have a W210 with OM606 3 litre turbo diesel engine (1998 in my case) ? To remove the inlet you need a T40 torx bit. Buy a decent make. I used a normal...
  4. M

    Simple one. Fuel hose W210 OM606

    Hi, OK Thank you guys, I changed the O rights on those clear pipes! I ended up removing the inlet and OMG it was evil putting it back on because the EGR valve clamp. I could not see it and could only get to it from under the car with arms/hands right up and hurting. Now it's been driving...
  5. M

    Simple one. Fuel hose W210 OM606

    Hi, Does anyone know how to remove the clear pipes so I can replace the O rights? It looks like a white plastic tab to be pulled but before I snap any off I would like to check. OM606 3 litre turbo. Getting air in the tube :-( Cheers Martin
  6. M

    w124 cluster removal tool wanted

    I have a gauge bulb out on my k reg 300te. I understand I need a tool to remove the cluster but do not have one. Can anyone lend me one if I sent beer tokens? Many thanks martin west Sussex.
  7. M

    W124 Water/methanol Injection / ignition live feed

    Joe. That is a great idea! So where is that relay ? lol I will be connecting a switch to the throttle somewhere so injection will only happen at the higher revs. :-)
  8. M

    W124 Water/methanol Injection / ignition live feed

    W124 Water/methanol Injection / ignition live feed Hi all, I run veg oil on my W124 300TD. I have installed my devils own methanol pump and some of the wiring along with the relay. I need a ignition live feed to complete the install. The pump is located in the boot in the place which housed...
  9. M

    Mercedes 220 fintail

    My mates dad gave one of these away. a very nice working one!
  10. M

    W124 Rear bushes neede

    Sorry for the delay! WDB 1241902F244344 is the VIN. It was on another plate years ago.
  11. M

    W124 300TD Engine mounts

    Also need the damper on the front of engine thats knocking away like a goodun
  12. M

    W124 300TD Engine mounts

    Its WDB 1241902F244344
  13. M

    W124 300TD Engine mounts

    Hi Franey, Thanks... Cheaper are ok? or worse? Just thinking I run this car on chip fat and it's not my pride and joy (got a classic for that) I would need 2. I will get the VIN. (guess thats under the bonnet) Many thanks Martin
  14. M

    W124 300TD Engine mounts

    I can not PM that person because I have less then 30 posts to my name. Rather then wunderpartz it's simply wonderful! lol Do the rear g/box that sounds a good plan!
  15. M

    W124 300TD Engine mounts

    Hi all, I own a 1993 W124 300TD. Does anyone have a link to some responsible priced engine mounts. Also are left and rights the same? Do all W124 have the same mounts (petrol/diesel) mine is a diesel. I'm guessing to change them out I need to undo the nuts/bolts on monts and the lift...
Top Bottom