Recent content by Webster200x

  1. Webster200x

    W212 e350 cdi - oil leaking - suspect crankshaft oil seal ?

    Hi, it was the oil cooler and I've replaced them but I've encountered more issues that I should have but all good in the end.
  2. Webster200x

    n3/9 motor electronics cdi6eu5

    Hi so got the car running it seems that two sensors were connected the wrong way ops but its running now but its losing boost it makes a sound like all the boost is escaping when Im accelerating and it shows up with these 2 errors (see picture) and there's also black smoke on the parts (also see...
  3. Webster200x

    n3/9 motor electronics cdi6eu5

    Hi, yes I did I've checked it 2 days ago with the multimeter and everything seemed to be fine and none of them were blown (didn't checked any of the relays) at this point should I just buy and replace sensors and see which one is actually tripping the car or there's something else I should check?
  4. Webster200x

    n3/9 motor electronics cdi6eu5

    I've cleaned all the connectors prior to installing everything back on the car and no errors prior to the oil cooler seals replacement and forgetting to tighten the two top screws on the turbo and lost a bit of oil in the process but the fuse that it blew was replaced and everything was cleaned...
  5. Webster200x

    n3/9 motor electronics cdi6eu5

    Can I unplug them with the engine running is it safe to do so? LE: So in this case should I replace the rest of the sensors and go thru them and see if it fixes anything or I should try to find a good mercedes specialist to have a look?
  6. Webster200x

    n3/9 motor electronics cdi6eu5

    Hi, i have a E350cdi 10 plate and i got the following error n3/9 motor electronics cdi6eu5 with the star code of this (pic below) and my car is in limp mode, I replaced the crankshaft and camshaft sensor but no joy says the same thing I've checked all the small fuses that i could see and they...
  7. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    Next week i might have some time to replace the camshaft sensor to see if the error goes away if not then i think i might need to take everything apart again and have a look.
  8. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    Fuses seem to be fine just checked them today any other ideas? TY
  9. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    Few updates, got the car started in the end but the car now start a bit harder than before and it goes into limp mode. Also in limp mode the gear changes don't seem to change properly is this because of limp mode and there's no boost at all the errors that i currently have and they don't seem to...
  10. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    Replaced the crankshaft sensor still no joy i'm kinda lost at this point any advice from a experienced member in what to check next or what if i missed something or what could cause the car the crank over and over and over and not fire up? ty
  11. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    Tomorrow I'm going to try and take the crankshaft sensor out to clean it and try again I'll also have a look at the wires again and see if I missed something.
  12. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    As i previous said the car started on the 4th crank after i did the oil cooler change but i forgot to tighten 2 screws on the turbo (the T40 or whatever they are) and oil started coming out and probably went all over the bellhousing soaking the sensors.
  13. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    Is it possible that my crankshaft position sensor to be full of oil and that's what preventing the car from starting? Also where is it located as i'm tempted to take it off cleaning it and putting it back together.
  14. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    So i scanned the car again and i got these. Now is this a case of taking everything apart cleaning the area and putting everything back together or might be that some connections from somewhere came loose?
  15. Webster200x

    W212 e350 cdi oil cooler gaskets replacement/questions for the assembly

    Ok guys a few updates, got the car back together started the car and to my luck i forgot to tighten the screws on top of the turbo and lost all oil (not a bit problem as i was going for a oil change) now i added some oil after i've tighten the screws but the car just cranks over but it will not...
Back
Top Bottom