Search results

  1. R

    W126 560 M117 V8 Crank position sensor

    G'day Al!. after much searching i found that Hella makes them! i spoke with Tom at the classic center and he was saying Daimler would only stock the Bosch part and this has left Daimler without stocks as bosch no longer makes them. He said he got a lot of hate mail over that ,because of all the...
  2. R

    W126 560 M117 V8 Crank position sensor

    Yep i had thought about changing the ignition something else (megajolt lite etc) but the car is set up so it's air con etc is working with the EZL .I'm trying to keep it so the owner can simply pop into a merc specilaist and they can service it for him. I have had megajolt on one of my own cars...
  3. R

    W126 560 M117 V8 Crank position sensor

    i have been building a car here fror a Customer weho wanted a 560 engine in it. i have rebuilt the engine (10-1 compression model) .A no start situtaion pointed to the crank sensor failure But.... Bosch no longer makes them and Mercedes no longer stock them . So i am stuck with the only option...
  4. R

    270CDi ML 2002 model year wiring questions.

    Hi, yes, i saw the vehicle it came from as it was few numbers close to the VIN on mine but a lot less mileage.
  5. R

    270CDi ML 2002 model year wiring questions.

    Hi, i've done that, i will try again though , i can pull that loom right through in the car i think but is there a 12volt feed coming from the F1 module to this loom?
  6. R

    270CDi ML 2002 model year wiring questions.

    Arrgghhh!!! OK, After getting a positive code read out which said one of the solenoids was shorting out,I dropped the sump and valve body. The contact was new (Febi ,with mercedes ID ground off) so i ran a multimeter over the contacts and solenoids. All of the solenoids are OK BUT ,the new...
  7. R

    270CDi ML 2002 model year wiring questions.

    A good mate came over with a chap who sells scanners and he plugged the very latest system into the car. Apart from a bunch relating to air con etc (all cleared OK) a code came up with message "P 2108 the internal electrical check of component Y36y2 (shift pressure control solenoid valve) has...
  8. R

    270CDi ML 2002 model year wiring questions.

    Hi, it's a replacement trans, the original disintegrated when a roller thrust bearing came apart. So I have flushed, replaced and refilled the trans which takes a touch over 8 liters ,that alone was expensive enough to make my eyed bleed..:D i have considered that and got the trans hot etc to...
  9. R

    270CDi ML 2002 model year wiring questions.

    I have scanned the shifter module and it didn't indicate any fualts. It's never had drink spilled down it either. I wasgiven one peice of asdvice regarding the shifter, always check the rod length adjustment and i did that with new nylon bushes etc and still the same result. :wallbash::D
  10. R

    270CDi ML 2002 model year wiring questions.

    Hi ,It's in a limp home mode:crazy:, 2nd gear & reverse only ,service due symbol comes up monetarily then shows odo reading and the tip tronic gearshift only indicates D etc. No 1234 on dash indicator. Cheers!
  11. R

    270CDi ML 2002 model year wiring questions.

    Well it runs out it was the air con compressor clutch lead . Someone has fitted an extra relay and a new lead to the compressor which threw me . For anyone else keep this as a reference ha ha
  12. R

    270CDi ML 2002 model year wiring questions.

    my ML recently blew it's trans (needle roller collapsed in the trans) so i fitted another. Prior to this the handheld scanner I have (carsoft) readout the code as P2502 . it still does despite me trying to erase it. What do Mercedes suggest could also be at fault with this code beside...
  13. R

    Wanted parts for ML 163113 Spare wheel carrier

    Hi Folks,I am trying to find a mount bracket to suit a ML spare wheel bracket as in the attached pic. Condition is not important .send me an email at briskiwi At bigpond.com.au :bannana:
  14. R

    W164 smokes at idle

    Full of oil ,as in flooded with oil? . If so the turbo ring seals are not working properly. The drain from the turbo should be easy enough tro loosen off and poke something through it to see if it is blocked,but it would be unlikely as there is a massive flow of oil through them. Have you...
  15. R

    Looking for M117 information

    :thumb: I found out this afternoon what model it was and the owner is"well chuffed " . It's a 5.0 liter M117-965 RUF 195KW at 5200 RPM and 10-1 Compression.:rock: The exhaust manifolds were a giveaway I guess. This model was introduced in the mid series around 1986 in anticipation of the...
  16. R

    Looking for M117 information

    Hi,Yes all the engine management loom is going into the W111. I suspect this is a 10-1 compression engine and as a result not much info is forth coming from the Yanks because they never had such a beast. The owner tells me there were no cats on the donor car and there wasn't an air pump on the...
  17. R

    Looking for M117 information

    This,It's a 1965 W111 220S with 36,000 miles from new :( if it were mine i would have preserved it's but it's the owners car....
  18. R

    Looking for M117 information

    I have a customer who wants me to install a 500 M117-965 engine into in his car which he has pulled from a donor vehicle . Does anyone have the tune up and/or spec sheets for the M117-965 engine?. It's From an ex Hong Kong 1986 car. We didn't get W126 500's here in OZ only second hand ones from...
  19. R

    Cat Question : Ceramic or metallic substrate ?

    Ours is fairly quiet but it has grey fur and is not ceramic..
  20. R

    E220 124T M104 engine harness

    We have quite a few car wreckers here which specialize in Mercedes, my local one even imports cars from the UK to wreck to meet demand,but the E220 wasn't sold here in big numbers . I have searched for a loom but none will sell a used one for obvious reasons. On this particular car the MAF...
Top Bottom