Search results

Good evening. I am having trouble with my alarm siren not working on my w203 ,lights flash but no sound. Changed the alarm ( new one is working as removed from my other car) still no luck. No lights on the switches on the dash to deactivate the alarm for towing etc. Could it be the module for...

Hi all. I have recently acquired a W203 C320 petrol , it has this hard start problem sometimes it will fire after 2 seconds sometimes I have to crank longer like 5 seconds before it fires up. And when it starts sometimes it seems to run a bit lumpy for few seconds then all good. Engine...

Hi. Does anybody know how to remove the parking sensors on 2004 W203 estate facelift ? Thanks

Hi fellas. I have this old 2004 W211 with 722.6 transmission. The issue is it has a slight slip when going from 1st to 2nd , worse when cold ,less noticeable when warm. Basically as you pull away the RPMs go up as they should till 1800 then they drop suddenly to 1600 with a slight jerk , then...

Hi. If anyone has w211 transmission undertray plz let me know via pm. Thanks

Hi I have noticed that right rear side of my 211 estate is lower than the left side , not by much I would say about 1 cm. It doesn't go down overtime and it doesn't go up either when car is on.... It seems to be set at that height. I noticed that the right side rear has had some suspension...

Hi. After last few days heavy rain , I opened the tailgate and to my horror water was pouring out of it , it was coming from between the black covering and the tailgate frame. Anyone knows the potential causes? Car is W211 estate 2003.

Hi. On my W211 2003 , I need my xenon Headlights leveling sensor calibrated , they are pointing too high dazzling others after some front suspension and welding jobs were done. If anyone Has DAS in Burton , south Derbyshire , Tamworth , Loughborough and surrounding please let me know.... I ll...

Hi. My W211 2003 has manually adjusted lumbar support , however its not working , the knob spins pretty much freely and nothing happens , I take it the teeth on the knob are stripped. Is there any chance someone could help me out and direct me how to remove the knob , cant see any screws or...

Hi . I am looking for a valve body for W211 C320 CDI with 722.6 transmission . Part number r2112770101 If anyone has it plz PM . Cheers

Hi. I have a W211 E320 CDI 2003 with 5g transmission. My valve body has an issue ( haven't removed it yet) and I am thinking to get a second hand one low mileage if possible. Found a few but they are from S class and SL and others. Question , are they all the same regardless of part number...

Hi I have a 2004 W211 with 5g tronic , apparently has been serviced in the past ) fluid wasn't burnt, but I sill did 3 sump dumps and checked level at 80c and was correct The issue it has is a slight slip on light throttle mainly when cold , when warm its fine. Usually happens between 1-2, u...

Wanted. PM if available

Hi. I replaced the strut on right side tailgate hinge on my W211 estate with stabilus gas spring strut same as the one I removed from the car. However I noticed the other side had Liftomat gas spring different to the one on right side , checked parts catalog and seems as the Stabilus gas...

Hi all ABS light on my W211 2003 Estate is on , changed sensor and reset but it came back. I presume the Impulse ring is shot. I ordered a replacement , but would like some advice in regards to Airmatic bellows , do they need to be deflated or disconnected from bottom wishbone in order to...

Evening. Just noticed that the rubber boot on my W211 estate rear shock absorber is in poor state torn in several places , I cant seem to find a replacement boot online. Are these non replaceable? Thanks

Hi. Does anybody know the part number for the retaining clip or spring that holds rear abs / wheel RPM sensor plug into the main block connector inside the rear wheel arch? Car is W211 See pic attached

Hi. I took off both front suspension upper control arms( wishbones) that sit at top of the wheel well. Wonder on refitting them wether I need to preload them before torquing , or there is an angle that they must be set at before final tightening regards

Hi. While working on the car today to my horror I discovered rome rot near upper wishbone mounting on both sides Would this cost an arm and a leg to weld ? Thanks

Afternoon all. Just getting around to replace the Injector seals in my W211 C320 CDI with two injectors blowing. I have purchased both MB copper seals and Honda ones , People out there recommend Honda seals which look thicker , may be 1mm thicker. Other says using Honda washer will raise the...