Search results

Sorry to bring up an old thread. Any pointers on removal? I have managed to disconnect all cables and turned the motor anti-clockwise but I can't pull it out. It feels as though something else is holding it in place?

Hi all C204, 2011. Any suggestions on how to shift out the blower motor, been trying since yesterday? It seems I can twist it but it simply won't come out of the housing, I'm conscious I might break something if I force it any further. Followed the videos - pulled on the tab, gave it a anti...

Hi all Was wondering if anyone could take a pic of their front right seat wiring to help the mess I'm in? It seems the previous owner cut the seat belt plug and I have no idea where it fits? I have the following blue and yellow wires which were soldiered to green/grey and brown. Now, I am...

Once again, thanks. I will probably buy a connector instead since I only have a small area to play with. If I heat use heat and damage the wires further I may mess the whole thing up. I think a small wire connector will also do the trick.

@John, thank you very much, I am not very savvy when it comes to electrics. What does it mean when there are red and black spots on the connector? Am I OK just to to connect Blue / Green-Grey and Yellow / Brown as per the image?

Got the dreaded front right malfunction consult workshop again. Having had a look under the drivers seat some wires were taped up to reveal the following! Seems they were soldiered back together by the previous owner which actually worked since having had the car for 4 years. I'm no good with...

Hi all I was wondering if anyone can shed some light. Last week whilst driving, the car was hesitant in stopping (felt has though the brakes were grabbing) a few moments later the ABS /ESP light came on, according to the fault code (C111200 - front right axle rpm sensor) needs replacing. Well...

Hi all Yesterday I replaced the rotary scroll shaft on my c204 (2011). Pretty simple job. Despite the shaft being exactly the same length the screw would not reach the thread on the shaft after assembly I bought the following from Amazon (see attachment). The scroll wheel now works but I can...

I cut myself twice both times whilst cleaning the car. First time I forgot, thought I'd buy glue and patch it back on..forgot. Second time, the cut on my finger was pretty deep. Got so annoyed just ripped the thing off. Looking at Chrome paints on Amazon but it's hard to find.

Hi all I understand this is a known issue for Coupe cars that have the chrome vinyl wrapped seat handle levers. My passenger side started to peel, little did I realize how bloody sharp it is. I have peeled half of it off. Not a chance I am replacing it since it functions and probably expensive...

I used to run Michelin pilot sport 4's, changed to good year eagle f1 asymmetric 5,absolutely great tyre and will be changing the rears for a set when needed. Defo reccomend.

Yes, you're totally correct, sorry to have asked. But equally, it should help any other members too. Never had this issue before in 16 years of driving, so as well as asking the members in this forum, it taught me a lesson.

"To be legal, a tyre must have a minimum of 1.6 mm tread over 75% of its width," This is very true! Thanks

Thanks HB - my mechanic said they was under inflated so they were pumped up. I am split between changing them as the center of the tyre is fine, like yours.

Had the car checked underneath and all seems to be OK as it recently went in for a water pump/brakes discs replacement. My question is does the tyre need replacing, is it illegal?

Hi all Passenger side tyre inner and outer edges bald, center looks OK. Image shows outer ware only, but it's the same as inner. Driver's side is fine, so it could be down to under inflation/alignment, but should this be replaced? Thanks in advance Ravs

Try unpairing your phone completely, removing all contacts prior and then repair your device.

If your mechanic has a star it might be worth resetting the adaptations. But before that try resetting the gearbox yourself via the Key at 2 position with 30 seconds on the throttle

Because I'm a dipstick, I stuck my finger in and guessed 🙂...

So.... My oil came, I poured it in the engine now the oil level is correct 😁