Search results

  1. M

    Viseeo mbu 1000 with blackberry?

    Hello again (and another query)! The phone paired fine and I can make incoming and outgoing calls work fine. I understand from other posts that this phone supports auto sync. So after pairing, I pressed the phone book sync button (while the green light was flashing) and it continued to flash...
  2. M

    Viseeo mbu 1000 with blackberry?

    Thank you for the very prompt reply. I have around 1200 contacts, so that would take a reasonable amount of time! Thanks again.
  3. M

    Viseeo mbu 1000 with blackberry?

    How long did it take the first time to sync the phone book? Reason I ask is that when I connected my BB 9780, the green sync light on the Visee0 was flashing (as I understand its supposed to) and continued to do so for quite some time and never stopped even after 10 mins or so. I figured it...
  4. M

    W211 Headlight manual adjustment procedure please!

    Solved ! A bit of research and the results for anyone in my situation: The knob marked "B" in pic above has a phillips screw inset which if turned alters the vertical setting of the low beams. The knob marked "C" in pic above which if turned alters the vertical setting of the high beams...
  5. M

    W211 Headlight manual adjustment procedure please!

    Hello again, The halogen projector headlights on my W211 2004 E 270CDI (non xenons) are pointing far too low. The foglamps are fine. However, the low beams point where the fogs are pointing and the high beams point where the low beams should ideally point. So, the headlights, though bright...
  6. M

    W211 Fuel filler flap "emergency" release access...

    If the actuator or motor that releases the fuel filler flap were to fail, you have the option of releasing it by accessing the release knob (which is not a knob but rather looks like a key) and turning it clockwise. Its located hidden away behind the trunk lining on the right side. All this info...
  7. M

    How to Remove rear license plate panel

    Success !!! Success finally :bannana: It seems it was a combination of three things that possibly resulted from possibly being rear ended and a poor repair job (during POship). Fortunately all sorted now. A brief recap for any one who finds themselves in a similar situation. Refer Post #...
  8. M

    How to Remove rear license plate panel

    Another try... The process of the last post (No. 11) was unsuccessful. So a bit further investigation by pouring water (in buckets) over the boot reveals that water is trickling from under the boot seal (between the seal and body), possibly finding its way in along the seal. Removing the seal...
  9. M

    How to Remove rear license plate panel

    Thank you, but not so soon...finger's crossed!!! Thanks you Alps, however its not rust. That brown stuff is the glue solution that the bodywork chaps probably put on to hold the rubber seal in place when they "apparently" sorted out the rear end and replaced the bumper. On the other hand...
  10. M

    How to Remove rear license plate panel

    Hopefully this time... Seems you have a point Alps... Looking around the area mentioned in post above led me to remove the trunk rubber seal and I found that the right side collar onto which the seal sits (where the leak was more pronounced) was about half an inch inset ie. it seems to have...
  11. M

    How to Remove rear license plate panel

    Thank you Alps. Will do and post...
  12. M

    How to Remove rear license plate panel

    Update: UPDATE: Under the rear bumper (fender) I found a metal part (probably the fender mount) bolted onto the bodythat has been bolted only on the left side (looking for the rear). The right side has a hole but the bolt is missing. I figure water could find its way into this hole and into...
  13. M

    How to Remove rear license plate panel

    I was wrong... The leak still persists even after clearing/removing the suspect drain seal. So, currently at a complete loss as to what to do...Will probably have remoe the boot lining and check.
  14. M

    W211 Glove box release push button

    The area around where the key is inserted on the glove box release push button is scuffed (paint pealing), proabably on account of rough use by the PO. I need to remove to remove this unit so that I can prepare and paint it. Don't want to do a masking job in the interior for obvious reasons...
  15. M

    How to Remove rear license plate panel

    UPDATE: I think I found the source... With a lot of help from Konigstiger who pointed me in the correct direction, hopefully, I will not have to remove the above refferred panel after all. There is supposed to be a drain hole at the bottom (refer pic below) and I found it had been sealed with...
  16. M

    Audio 20 front display plastic replacement?

    The most likely possibilty!!! Thank you...will look it up. Thank you for the offer, will consider. Nope, not an import. The E270 CDI was available from 2003 till 2005 alongwith the 220CDI & E240, E200K. With 2006 and the facelift, the 270cdi (L5) was replace with the 280cdi (V6).
  17. M

    Audio 20 front display plastic replacement?

    OMG!!! Thats absolutely correct. For some ridiculuous, inane and inexplicable reason I have been calling it the Audio 20 :confused: ...Apologies. I guess I am stuck with the cracked plastic plate... Thanks a lot. Wonder how the PO managed to damage that?
  18. M

    How to Remove rear license plate panel

    Actually I did remove the torx screw you refer to and still found it to be stuck. Is there some kind of lock / clip etc. that is holding it in place? Ok thanks. No fear of breaking the plastic panel? I did lift the panel away form the metal body while turning the bolt, but it went a few...
  19. M

    W210 E220 CDI (2001) vs W211 E200 KOMPRESSOR (2004)

    Really apologize for not replying earlier...:doh: Its MY 2004 genuine 34000kilometres on the odo with full service MB authorized dealer history. Apologies again.
Back
Top Bottom