Search results

  1. L

    W124 coupe b pillar seal

    Thanks for that, any ideas on part no.?
  2. L

    W124 coupe b pillar seal

    Hi would anybody know the part number for the small upper door seal that fits under the chrome finisher plate at waist level on the b pillar? My dealer cant find the seals? Thanks
  3. L

    W124 ABS fault very annoying

    Hi sorry for delay in getting back, the light goes out if the main relay is pulled so it would appear that everything bulb wise is OK, tried the brake light switch but it only has two wires so only contacts when the pedal is pressed and the brake lights work and I get 12V at the ECU when the...
  4. L

    URGENT HELP with possible alternator / battery problem

    The pulley can be changed in situ but you will have to remove the fan/cowling and multirib belt, you also need a special tool to hold the pulley when undoing/tightening etc available from Laser or Sealey tools
  5. L

    URGENT HELP with possible alternator / battery problem

    Hi make sure the alternator pulley is actually driving the alternator, what can happen is that the freewheeling pulley can slip in the drive direction thusc free wheeling both ways. Many alternators with freewheel pulleys are changed when they only need a £35 replacement pulley. Checking the...
  6. L

    W124 ABS fault very annoying

    Thanks for all your combined help on this chaps, just reassembled everything back into the car hoping for a miracle cure but still no joy. Drove the car for a mile in the hope that it may reset but alas no. Will double check the brake switch though [ the brake lights do go on and off when the...
  7. L

    W124 ABS fault very annoying

    Hi Ian, I have already replaced the pump and relays which made no difference, does the car have to be driven to clear fault codes?
  8. L

    W124 ABS fault very annoying

    Thanks for quick reply, the alternator puts out 14.5v and the ECU is seeing this on the blue red voltage sensing wire, I cleaned all the earths on the ns suspension tower and the pump to chassis leg. I know if all these are OK then it should work thats whats so annoying. On my other car the...
  9. L

    W124 ABS fault very annoying

    Hi we recentley bought a 95mwy E220 estate the ABS light was on and we stupidly thought it would be a simple OVP fault or at worse a speed sensor issue. The light is on at all times even with the car staitionary, it flicks off for a second when the ignition is turned on then immediatley returns...
  10. L

    SLK320 weird throttle fault!

    Sorry just reread my post its the ignition that as to be flicked off and then back on to enable the throttle to work correctly
  11. L

    SLK320 weird throttle fault!

    The car will only rev to 1500rpm staitionary or moving until the throttle is flicked off and then back on without letting the engine stop, then the throttle works perfectly until the ignition is turned off. The fault then reoccurs
  12. L

    SLK320 weird throttle fault!

    Can anyone recomend a good ECU test repair company other than BBA?
  13. L

    SLK320 weird throttle fault!

    Hi can anyone throw any light on this fault? The car is a 2000my SLK 320 manual, if you start the car normally at any time the throttle doesnt function, full throttle just manages to lift the revs up to about 1800RPM, I have read the fault codes and get a code for faulty throttle actuator or...
  14. L

    W209 intermittent brake failure

    Hi, if we leave the car standing for a few hours on returning the brake pedal goes right down,if the pedal is pumped it returns to normal and works fine for the rest of the day! Initial thoughts are brake master cylinder but dont want to splash out until sure. All pads calipers discs OK no leaks...
  15. L

    W203 battery/ alterntor warning

    Sorry for being short just a bit frustrated with getting to a dead end at the SAM, I have 14.7v at the SAM and a running signal on curcuit 15 at the SAM, But how can one test the SAM output to instrument cluster? I guess this would be a Can signal
  16. L

    W203 battery/ alterntor warning

    Getting the red warning message, checked voltage output at 14.5V alternator pulley looks fine, could this be a front SAM issue? No fault codes Thanks
  17. L

    W203 AC not working

    Looks like we loosing pressure signal at the front sam? tested wiring continuity rom condenser sensor to Sam and alls OK, question now is do we throw another £250 part at this fault
  18. L

    W203 AC not working

    No Iam only getting a constant 0.06V at the comp any ideas on the ideal voltage I have been told that this is a pulsed varible voltage for the variable displacement comp? Does anyone have a decent wiring diagram for the AC? Autodata shows the condenser temp and press wiring terminating at the...
  19. L

    W203 AC not working

    Fitted new sensor but still zero press reading?
  20. L

    W203 AC not working

    Strange but true the car is now logging low ref press fault! The live readings are showing zero for condensor temp and press? Yesterday we had readings but not very high, going to try press/temp sensor next? Just hoping its not a control unit issue. Any other thoughts?
Back
Top Bottom