• The Forums are now open to new registrations, adverts are also being de-tuned.

bolt

  1. babyblueCE

    Wheel Bolt problems

    Hello all. Need to rattle your brains as i am having difficulties in finding the right size of wheel bolts for my wheels. I recently purchased 18" rep rims with ET35 and my mechanic has advised that he can't find the right size bolts to fit the wheels on, either they are too small or too long. I...
  2. imbck666

    w124 crank bolt removal

    Hi all, Just a quick one really.. Dropped a bit of plastic through the gap where the duplex chain is in the timing chain cover and now i cant hand crank the engine... The plastic has siezed it, so need the timing chain cover off asap. To take it off I am aware that I need to take...
  3. effbee584

    CLS Crossmember Bolt & Bush missing?

    Had my newly acquired CLS on a ramp in a tyre place today and the fitter pointed out what he thought was a 'missing' bush and bolt. The picture is taken looking forwards with the diff just forward of the crossmember. The screw thread showing is clean and shiny. There was some rear end work done...
  4. Alps

    Genuine Mercedes Locking Wheel bolt set

    Brand new unused locking wheel nut set for use with 12mm thick bolt NOT 14mm. threaded part is 27mm long and total length including head is 48mm (as ive already got my tape measure out!) part number B66470144 Bought for my w211 E55 but it has a 14mm thick bolt. will fit for...
  5. shanksy

    Head Bolt Tightening

    Morning all ! Ready to put the cylinder head back on this morning...... ('94 e220 Coupe W124) The manual I am using however contradicts itself on the tightening of the head bolts. In the text it says to tighten in the correct sequence to 40 lb/ft, then turn a further 90deg However the...
  6. kieranswood

    Stuck on the bottom bolt of the distributor cap any help appreciated

    I have my replacement cap and rotor but have got 2 out of the 3 dis cap bolts off, but the third on the underside seems impossible to get too with any Allan key or bit can any help? Thanks
  7. Smarties

    190E 16V Wheel Bolt Part Number

    Hello Fellow forum members. Can anyone help me with part number/s for the wheel bolts to fit the 190E 16V Alloys? I have a set of 16V wheels languishing in my garage and I really must get them put on my 190E 2.6. Thanks in advance
  8. S

    SL 55 Wheel bolt length. Help please..

    Does anyone know the length of the SL55 AMG wheel bolt. Thread length please? Thanks in advance. Steve
  9. O

    Front lower wishbone bolt and nuts W210 and others

    Here we go, 2 brand new bolts and nuts for the lower arm suspension. cost over 18 pounds at MB, for sale shipping included at 13 pounds. Cheers. parts: bolt: N308765014022 Nuts A2029900851
  10. R

    W211 Towbar -Wing Strengtheners - Bolt Size?

    Can anyone tell me what bolt size to use to fit the wing strenghtening plates on a W211? Bernd
  11. SilverSaloon

    Subframe mount bolt sheered - solution

    Hi I decided to replace my rear subframe mounts ("front" ones). These were duly ordered from Franey (i got them almost 2 years ago but not fitted until now!!) Olivier came round to help (thanks again mate!) anyway, it was a bit of a squeeze but we managed to get the old bush out and squeeze...
  12. M

    Wheel bolt caps

    I have a set of the extended wheel bolts with the cup half way down the bolt, but the faces of the bolts looking fairly grim. I've tried to purchase replacments, but these are apparently nla. I've also tried to purchase just the end caps, but the dealer reckons these aren't available...
  13. O

    tie rod bolt size? E300TD

    Hello, I need to change a tie rod on the E300TD, what is the spanner size needed for the end that goes into the steering rack? Or is there some other tools instead of a spanner that I can use to un-screw it? Cheers. Olivier
  14. Alps

    caliper bolt torque

    Need some help here please just been replacing my rear disks and pads on the e55, fairly straightforward, just a pig to get off the handbrake shoes. my question is,how do you guys tighten the caliperbolts to 180 nm when the car is on a jack? my torque wrench is massive and just cant get...
  15. W

    Where to find wheel bolt seat radius?

    I have some 16" Toliman wheels and I need to find out the radius of the ball seat so I can buy some new bolts to the correct specification. ?
  16. mbzclk

    stuck locking wheel nut bolt.

    what not to do!! http://www.honda-tech.com/showthread.php?t=2684546 :eek:
  17. sspeed

    Wheel Bolt size for a C270

    Hi everyone, Can any of you give me the correct wheel bolt dimensions for a W203 (C270 CDi).. I am thinking of replacing the wheelbolts with some less corroded ones. I have been on a well known website that sells original merc wheels but there seems to be 2 bolt lengths listed.. Thanks in advance..
  18. BAD300

    Will 300e 722.320 (stock 4 sp) bolt to the 500 sec (M117 engine)?

    As title says, will the 722.320 4 sp auto trans bolt to the M117 engine. Car in question is an 80's 500 SEC
  19. CHRIS STARKEY

    Anyone please tell me what this bolt is?

    Hi, I am trying to locate the top of the rear shocker on my 2001 E320CDi estate - is it this bolt in the attatched photo? According to my book it should be a nut rather than a bolt! I don't want to undo it & something fall off!! cheers Chris
  20. A

    Fuel can securing bolt

    I'm looking for the long wing bolt that holds the [Mercedes]fuel can into the spare wheel. Anyone got one of these they don't want/need?? Thanks Chris
Back
Top Bottom