cylinder

hey wondering if anyone can help my clk has just produced a misfire on cylinder 2 but when I turn the car off and on again its fine until I put my foot down and then tho and behold misfire again... would this be a cause of a coil breaking down????

i have a cylinder head off a 1998 e300td just wondering what the value of it could be

I will try to be succinct with this so here goes:- Car - 2009 A 180, petrol with BRC lpg conversion (inc valve lube kit) 80,000 miles pretty well trouble free until a couple of thousand miles ago. Fault - ocassional misfire on starting from cold which also closes down cylinder 1 making it...

If you are doing a rebuild or engine repair, before considering re-bore and oversize pistons how about block repair and coating? Cylinder bore coatings by Poeton – Apticote 2000 Before After Poeton Apticote Ceramic 2000 is the premier cylinder bore and cylinder liner coating...

Hello everyone, Does anyone know where I can get a cylinder head from the M180 2.2l 6 cylinder engine. Secondly, does anyone here have any experience in fitting one to a unimog 404 engine? Thanks

Just took my E320 cdi WDB211 for servicing and MOT to my dealership, got a call back saying all done but MOT failed due to excessive smoke from exhaust. ( did not have that problem before). Probable fault with the intercooler turbo as it appears to have a leak.. due to accidental damage...

Hi all I was driving along today, went over a pothole and then could hear something dragging along. It was a black cylinder of about 4 inches in length and maybe 1.5 inches diameter with a wire going to it and a wire coming from it dragging along the ground just inside my rear drivers...

Following from one of the threads where a member was concerned over the refinement of C220CDI engine. The 4 cylinder diesel from Mercedes are not that bad, and is quite refined when you're inside the car, plenty of poke and power. However when considered further back, and I probably will...

Hi, I'm still really enjoying my 500 SEL. I've done 30,000 miles since I bought it in 2010 and it is going well. However, I'm getting slight brake drag now, and the front brakes are slow to release sometimes, despite the car having new flexy pipes, callipers and pads (which move freely). I...

changed coil pack plugs also did timing chain and breader pipe under air box any ideas

Hi guys Could anyone confirm the correct numbering sequence of the 320 cdi V6 engine cylinders. I think it's (looking from front) drivers side 1,2,3 front to back and passenger side 4,5,6 front to back. I'm comparing the injector numbers to the ecu programming and just need to be sure. Thanks

Hi Guys, Im retrofitting C63 Brakes onto my C350cdi and I've been trying to find info on the master cylinders. Ive seen 3 conversions done and working perfectly without any master cylinder changes. Any thoughts?

Hello All. Hope someone can help,I purchased the above van knowing it needed a water pump(so i was told) it was a pig ov a job put it back together again filled with water to find it pouring out,ont the back ov the engine above exhaust manifold rhs is where its coming from,is this round hole a...

So I'm looking to replace a cylinder head on a 2003 C220CDI coupe due to damage done when previous owner tried to remove a snapped plug, anyway I can find cylinder heads for this car but none which are the exact same part numbers. Are all C220CDI cylinders the same? Thanks

Hi there, Its a stab in the dark but after a Master cylinder for a 2004 C180k, must be brand new. Thanks

Hi there, I have a w203 c180k 2004 and need a master cylinder. I can't find any on the net and Mercedes are 249+VAT, don't really want a second hand one as it will be untested and especially as it seems to be a common failure. Does anyone know who makes the master cylinder, did see...

As above in good condition, removed from a 1997 s280 with 89000 miles. Comes complete with cams and valves, will fit 2.8 or 3.2 m104 engines. Open to offers via pm.

Hi all, as some of you know i am doing the head gasket on my w124 e320 TT. I have dismantled everything and got the head off cleaned it up a little but i need your opinion on if it is ok or not. There are two issues, main is highlighted below. I have to options, either get a new head for...

I need a cylinder head cover for a 2.8/3.2 M104 engine which is in good condition. If you have one, please let me know ASAP. Its for the early M104 engine, not with the centre black panel. Thanks.

Hello, Anyone ever heard of these people ? I just called to ask if they could replace an injector seal on a Vaneo (A Class), and the bloke sounded as if he knew exactly what he was talking about. "Oh yes, what happens is the clamp works loose and we have to helicoil it and reseat it. Should...