eml

hi all thought I'd ask as can't afford a big bill as off of work at the moment due to cutting half my finger off, I've had the car about 5 weeks now and it's been great but after owning it 2 weeks the eml came on with the code p101 saying its the maf sensor so I replaced that with a vdo one from...

I went to overtake today. Whilst lots of throttle the power cut and eml came on which I guess is limp mode. Pulled over and switched off. Started again and have some power back but eml still on. Can't get on a star unit till Friday. Might be coincidence but car had a service 2 days ago?

After Diagnostic this came up: 00F8-004 Plausibility check of values for B28 (Pressure Sensor) and M16/6 (Throttle Valve Actuator) in idle and medium load Lambda control OK What could be the cause of this? Much appreciated Thanks

Looking for advice here car lost power today then after 30 mins driving eml came on then got full power whats the best code reader to check out ma issue

Hello all, A week into ownership of my S204 C320 CDI i have run into problems with the EML light on, and the car reverting to limp mode. Car was attended by breakdown organisation this morning, and Error Code P2015 identified, which appears to point towards Intake Manifold Runner Position...

Hi Chaps. I had the engine management light on my E430 and needed a new Lambda Sensor. Had that fitted and all was ok apart from a minor misfire at idle. A week later I added some STP Complete Fuel System Cleaner and the misfire has diminished but now the EML is back. Could the STP be...

Hi guys, I have an annoying vibration from the airbox when the engine is running, which goes away if you press on the top of the box, so today I took off the lid to see if there is a rubber seal of something missing. Around the edge of the underside of the lid, there is a groove, but not sure if...

My cousins 2003 A170 CDI has come up with the EML on the dash. The car also feels sluggish and slightly underpowered at the moment. I have plugged it in with a universal scanner and it comes up with error code P0034 - Turbo charger bypass valve control circuit low. Any ideas ?

I changed the oil and filter on my Vito 120 Sport earlier and now have the Engine Management Light on and the van is in limp home mode. Before I call Mercedes Assistance, does anyone have any idea why the EML might be on? TIA. Paul.

Hi All, I am new to the forum. Hoping some of your experties may help me identify my issue. I have a 2004 C270 CDI. My engine management light (eml) came on a few days ago. I took it down to my local Benz specialist (not MB) and he ran a diagnostic on the the car; diagnostic showed no...

Got a 2003 A160 with the EML light on. Have read the codes and it comes back as: Stored DTC P0600 Serial Communication Link Malfunction Stored DTC (pending) PO335 – Crankshaft Position Sensor A circuit Malfunction PO600 – Serial Communication Link Malfunction When you try and reset it...

Hi guys Last night my 220 cdi starting making a funny sucking noise when under load. Then it was all silent and i lost most of my power. My mate took off the egr and cleaned it but it wasnt closing its self when he manually opened it, is this normal? My engine management light also came on...

As above with no running problems. Any ideas? Ni Anyone know a good indie around sutton sururey area? Tia

E320 cdi, w211, Hi, Had it into indie a few weeks ago regarding eml light on and a few other issues. Told can bus system not communicating but eml reset anyway but unable to reset old issue of srs light on(car previously bumped and air bag replaced). Left it at that as I can live with srs...

Just had the inlet port shutoff motor replaced because of the common oil leaking from the turbo problem. Still showing the following current codes. Does anyone have any idea what cause these. 2530-002 Check component M55(Inlet port shutooff motor). Short circuit to ground 2527-002 Check...

hi all i have a clk 200k, w208. now i have had the car for 2 weeks and when i got it the guy i got it from told my the eml had come on and his mechanic had cleaned the maf sensor and the light went out. now the light has come on again, is it likely to be the same problem and am i right in...

I have a late 51 plate C class 200 komp and have had to get the eml light switched off a few times without ever having any problems, so i am now looking at getting the tool to read and reset the codes. Could anyone tell me what tool i would be looking for and where is best to get it, thanks.