injector

Hi everyone. Does anyone know what injector bolt and washer is the same as a vito 02 112cdi. I have spoke to main dealers near me and they don't do commercial parts (5 mins away). I can get vito ones but there 20 miles away from me and they say they don't see part numbers. Any help would be...

Hi Everyone I recently bought a 2003 ML 270cdi with 160,000 miles on the clock and it had a couple of blowing injectors (three and four if counting from the front) - the dreaded "black death"! After reading the threads already on here (Very useful too, thankyou!) I decided that the removal...

Hello I need urgently a 190d 2.5 diesel bosch injector pump. Cant seem to find one anywhere. Does anyone know of any. Tom

Hi folks. I wonder if any of you have come across this issue before. I removed the engine cover today after getting the smell of exhaust fumes in the car and where the injectors and wiring all sit i had a melted mess of plastic. It seems its had an injector leak for a while (ive recently bought...

Hi all We had a problem recently where our ML270 was cutting out completely at random. Our mechanic identified the problem, the 'black death' of a leaking injector seal had screwed up the electrical socket on the top of one of the injectors. He has done a temporary fix with spade...

Hi, I have just bought my wife a 2002 a170 and it broke down immediately. Took off the air inlet manifold and found a broken injector pipe due to the one of the injector clamps not being tightened. I've bought new parts but need to know the torque settings for the injector clamp and the air...

I'm starting a new thread because its relating to the correct procedure for repairing an injector. Can someone tell me what is the best thing to do here. Injector 2 has had some work previously because the bolt came out with helicoil on the end but onbviously failed, what is the correct...

Hi, have 2 blocked Delphi diesel injectors....MB Melbourne saying cost each AUD $1,500 and on back order with MB in Germany. Is there anyone aware of an aftermarket injector (Bosch or similar) or someone in Melbourne that can at least test them or repair/clean the existing? Appreciate it.

Hi Ok during a nice beer fueled evening a subject come up about plug n play injectors on vehicles before the introduction of the piezo type. We discussed the Fiat group diesel injector coding agreed and squared that away and loosely agreed on VAG as well, but stumbled on agreeing about Mercs...

I smell something not right from the engine so I open the engine cover and found the black oil over injector no4. Please anyone know what's wrong? Is it expensive to fix? and I need to use the car to travel to work at least one more week would it be ok to drive like that? sorry for my...

I've got a 2000 W210 E320 CDI straight six and today I popped a load of diesel fuel system Redex into the tank and within ten minutes the injector nearest the bulkhead (rear of engine) blew out because the bolt that holds the little forked retainer in has been seated in a helicoiled hole. My...

Hi Been sent a snap shot but my Star's at the workshop for the weekend. Are the injector values allowed +/- 5mm^3/Hub or +/- 3mm^3/Hub I think they are 5 but cant remember Thanks all :)

Does anyone know a good upgrade seal for the e320cdi, had all my seals and bolts done 3 months ago and now No.2 is leaking again, I did use genuine merc parts but have heard that there is better washers that can be used

Hi just bought a Vaneo 1.7 Diesel which was chuffing. Managed to remove the stretch bolt but not sure how to remove the clamp its self. Dont want to force it and damage something. Can some one tell me how to remove the clamp please Thanks

Just a bit of info guys, bosch don't list flow rates, some sites do and always seem to contradict each other, I have had various ones tested at 5O psi over 30 sec and good / clean will flow 114cc, most of the ones that had tested had flow rates going from 108cc to 112cc this would normally cause...

1998 c250td Can't get any pressure to injectors,no air in system ,any ideas.thanks john.

When I try to tighten up the retaining bolt on fuel injector it's just turning and not gripping, do I need to get new head aaarrghhh:dk:

Can some give me, or post me a link to a step by step guide on replacing the injector seals+clamps etc on a ml270 (w163) please. Also any special tops needed? Thanks in advance

Hi guys, As some of you know I stripped my car to do the cam covers, but decided to powder coat the cam covers and inlets, also removed my fuel rail, and put the injectors in for flow testing and cleaning, some of mine needed cleaning 4 or 5 times, now the flow is perfect across all...

I have an ML270 CDI (2002) and had a 'chuffing' injector. So searched and found the advice on how to fix it, seemed quite simple, so went off and bought 5 bolts and washers so I could do all of them. However on undoing the number 3 bolt (the one that was chuffing) I found that the thread was...