inlet

Hi all I know that my inlet manifold/swirl flaps are very probably worn out - poor performance, oil down side of engine block etc. Not knowing a vast amount about the inlet manifold, if I do the EGR blocking off and electrical modification, would it be necessary for me to also replace the...

Well all i can describe replacing this job as is a right pain in the **** !!!!!!! Car is a 2008 E320, full main dealer history and 100,000 miles on the clock, car darted loosing it's kick down and turbo...sort of a limp mode, no MIL on dash board, but it was just not right. Car went onto...

Hi all ive got a clk320 cdi, i had an issue with the shut off motor due to oil ingress, rather than replacing it i decided to remove the entire system. I followed a thread by Alex crow, however the flaps on the v6 are different, they are not held in with a torx screw. They appear to be riveted...

Just been told my manifold's need replacing on my E280 V6 Anybody else have this done and at what cost??

2513 (inlet port shut off motor) positioner signals fault Just had the RAC out, confirmed above fault. I had the inlet port motor replaced last year, is this the same fault? Anybody got any ideas what cost I could be looking at? Gutted as I'm looking to get rid of the car and can do...

evening, so ,for a few days now the ml has felt a bit sluggish/underpowered,thought it might be the maf so swapped with a spare i have but still the same, took it down to local indie to put on star and it came up with the inlet port shut off motor,mine is cable tied up to bulk head for...

annoyingly, even though i have a breaker sat on the drive, both inlet rubbers are split. Its the one that joins the cross over pipe to the plenum chamber on the left of the engine. Short, 80mm diameter, same both ends. Anyone got one, or even a price new from merc? Thanks

Hello everyone Yesterday I took my W203 2001 C200 CDI to service because of diesel smell in the cabin and the leak was in the pipelines. Anyways the mechanics had noticed while finding the leak that my turbo is leaking and that has also caused the inlet manifold to go bad! I didn't have too...

Hi All, I've just done a mod (thanks to Alex Crow) to fool the ECU with my faulty inlet motor. I now have a couple of codes P0130 & P0135 is this likely to be just the o2 sensor or is it a false reading and caused by a stuck inlet valve? Thanks

looking for an e300 manifold so i can cut it down and modify it for an om605 engine. cheers

Evening all, It's that old chestnut again, started to remove the inlet manifold on my 2003 270cdi and have got to the bit where everything is unbolted on the top side and all the manifold bolts are out, but, there is a couple of fuel lines and two electric wires going down into the lower part of...

Anyone got this?

Hopefully going to do this next week when I'm a bit better. Want to clean it out as well as the EGR as I'm sure it's never been done. Will do the EGR delete afterwards. I have read through many threads but cannot find difinitive answers to a few questions. Is it relatively simple? I am...

Does anyone know any good indies in Manchester who will be willing to do the mod to my existing manifold? Literally take it out, modify then re-install? My indie won't do it and they want £800 to fit a new one with new motor.

Used part, removed from my car as it was replaced when having the inlet manifold changed. This part is in working order and pulled from a running car. It's an original Mercedes part - made by Pierburg. A 642 150 01 94 - Number on the part Same as A 642 150 04 94 Check with local dealer...

Have booked ml into local indie to get my leaking alternator looked at. Whilst in I've asked them to check my manifold as the car feels sluggish, kicks out black smoke on acceleration and has oil down the side of the block. Does anyone know how much I should be paying for a direct replacent...

Hi everyone, I have a W124 230E and I think that the stock muffler's inlet is 55-56mm. So I am tempted to buy this muffler which has inlet size of >57mm but I have some doubts to clear. If I fit this muffler on the stock exhaust pipe which has different diameter size, would there still be a...

I have never been happy with the Mercedes inlet gaskets, and the fact they are use once, having had to remove my inlets on 3 occasions recently for one reason or another, was looking for an alternative solution, even lazer cut stainless, in the end opted for reusing my merc gaskets and a product...

Does anyone have a spare air inlet Y piece for a CLS55, lower clip has snapped off, and seems you cant buy the pipe on its own now.

This Mercedes v8 4.3 engine was taken from my own personal car that I unfortunately had to break for spare parts, it really is a great runner smooth as silk with plenty of power. This engine is fitted with a amg inlet For sale is the complete engine with harness, alternator, power steering...