manifold

I am working on 06 freelander with the BMW td4 4 engine , if I plug the map sensor out of inlet manifold while engine is ticking over and after plugging Sensor out it makes no difference is this a sure sign sensor is not working. I joined a land rover site but advice is very thin on the...

Hi every one Im new on the forum, done some reading and found interesting topics. Hope you can help me. I have a 2005 Vito 115 W639 engine code 646 It goes into limp mode if rpm goes over 2000 I get the following errors from my ELM327 WIFI module connected to my iPhone: P2018 Intake...

Hi, I've just bought a 1969 280s W108 and working on some carb issues. I,m curious about the balance weights sticking out of the inlet manifold which I can see are linked to some sort of flap assembly. See bottom right of attached image. The weights seem to be solid or ceased. Should they be...

Hello, I'm looking for an OM606 inlet manifold to chop up so condition not that important. Let me know what you have. Thanks

Hi everyone I hope I am putting this in the right place About 5 months ago i bought an 03 c200 1.8k coupe (auto), overall I am very pleased with the car, its not the quickest off the line but the compressor engine is very willing and pulls like train, the car has only covered 70000 and has...

Hello, Does anyone have a diagram or layout for the manifold which holds the Turbo on the drivers side as I need to replace the gasket due to a leak and just wondered the best route to take as the bolts are in very difficult to reach places. I am guessing the turbo needs to come out to...

Hi, finally getting round to sorting the EGR fault. Ordered a complete second hand manifold with EGR, cooler and swirl flap motor. Going to clean this up ready to fit. Does the inlet use a gasket? Someone has told me it is reusable? Also going to do the fuel lines while I'm at it. Anyone...

Hello, I have an issue with my 2006 C220CDI. It has developed a rattle noise and signs of oil leaking from the connection to the intake manifold. as illustrated below. Also when the car is in motion there is a very noticeable whine coming from the engine under acceleration, this seems to...

Hi What's the function of the hose that goes from the lower crankcase to a t connection between the intake to cylinder 2 and 3? The bottom connection to the crankcase is leaking oil.

Just curious, what would a stock 2013 E63 5.5TT be seeing in terms of maximum boost? what about an 'S', and what about a mapped car?. My torque profile seems to be showing low boost .. < 1bar. What should it be reading? Cheers, Alex

Hi guys anyone got one of these spare?

Afternoon all, seems like my car has a common issue for M272 / M273 engines (lots on the web about it) but I couldn't find anything in the forum archives here. I've got the check engine light on my CLK350, 55 plate and the OBDII reader shows P2006. It used to come back every 200 miles or so...

Hi everyone, Hoping someone can help me, my C230 started throwing up a P2006 code and after nearly passing out from the quote to repair it from a local indy I started googling about and found the repair kits and cracked on with pulling the Intake Manifold off. Whilst the lever is snapped...

:bannana::bannana:well i changed the manifold at the weekend and tbh not as bad a job as some people have said,that said you do need to have some mechanicail know how about you,i saw that some say you need to remove the fuel rail,no you don't but you will need to unbolt it and lift it,of course...

Does anyone know what the torque setting are for fitting the manifold to the block?cheers:wallbash:

Hi just after a bit of advice,my ml won't rev above 3000rpm and there is no pulling power, i did a check on the ecu and its come up with inlet valve port,I'm guessing it means the stepper motor????? are the flaps open and the motor closes them or is it the other way? cheers for the help in...

I know I should be able to find this witrh a search, but I haven't managed yet... I'm looking for the Part Numbers for the Inlet manuifold seals on my ML 320 2007, so I can order them. There are two of them that leak oil after a few years and cause other (more serious) problems. One seals...

I have a small oil leak (an annoying drip or two each day making a mess of my drive!) my local MB garage (Hertford) tells me it is the inlet manifold that needs replacing. However, the cost quoted at an MB garage doesn't seem worthwhile for the age, 2005. Does anyone know whether there is...

Have mod intake manifold of my w211 270 cdi 2004 .i have removed all flaps inside manifold . What do you think ???

Hi all, As per the title. Thanks