manifold

hello all im new to this club... my situ is this... i have a clk 230 2001 model. In 2007 i had my exhaust manifold changed by mercedes which cost inxs £800.It lasted less than 2 yrs (just less) and went again along weld in the center of the manifold. Fortunately the warranty was 2 yrs and i was...

Hi can anyone recommend a good mechanic To take off my inlet manifold & remove the flaps I have a funny noise & oil leaking under it. In the Walsall area or Birmingham. Also what am I looking at in time it takes and cost anyone help please.

Hi All, My exhaust manifold is leaking and needs welding up. I need to remove it and at 1st glance it looks like I need to remove the super charger, although I've read it can be removed without touching the super charger. Does anybody have a removal procedure (that hopefully doesn't invole my SC?

Hi does any have a e200 W124 exhaust manifold, it's the late 1995 16 valve model. I'll collect from all over yorkshire, upto Durham, North Midlands and Lancs. I also need the heat shield.

Hi all, The exhaust manifold on my 1995 e200 is cracked, would the manifold from a e220 coupe fit. It's just that I can get my hand one cheep and as I remember from past ownership the manifold looks a better design to get rid of the gases. Cheers

hi guys need some help. Started to remove manifold but I have got a problem. I have removed most of the screws but I'm having trouble with the 1s at the back (bulkhead side) its only 2 and it's the 1 above and below that are the issue. I can't seem to get a socket on them. Anyone got any tips?

Hello mates! today i took apart my inlet manifold on my e270 cdi, w210. the car was in limphome with faultcode p1189. It was a little oil in the presurehoose, and the EGR was completly full with black sh*t! When i came to the inlet manifold i saw that only one rod was conected to the...

Hello dear mates! I have a e270 cdi that runs in limp home now, took fault code and it says p1189. The manifold flaps are jamed or not working, i need to remove the manifold and clean everything and then i have read somewere that you could remove them quite easy. a new manifold, motor and...

Hello all; just priced up a replacement exhaust manifold from MB in Newcastle and nearly fell off my seat £560 without gasket set. Any one got any less expensive suppliers? Not tight but for the age of the vehicle I think the preverbial is being extracted. Paul:wallbash:

This piece is placed in order to protect the inlet manifold servo. The inlet manifold servo is a well know breakdown in this kind of engines just only consult it on MB forums to confirm. The cause of this failure is the hot oil that falls down in the servo who rules the admission. This piece...

Hi all, It was going to happen some day. I was checking the engine bay over and I think I can see oil running down the side of the engine block? More so, I think I can see it flows back towards the back of the engine. (A bit difficult to pick up on a camera) The car is currently driving...

Hello, This piece is placed in order to protect the inlet manifold servo. The inlet manifold servo is a well know breakdown in this kind of engines just only consult it on MB forums like this to confirm it. The cause of this failure is the hot oil that falls down in the entry of air in the...

Hi Gents, Would appreciate some advice here, if anyone has had the same issue. My car has been stuck in limp mode with the engine management light, after having it diagnosed, the error came as the intake manifold runner sensor. They dont know weather it is the motors or the whole manifold...

Mercedes 190E 190er W201 2.5-16V EVOLUTION TURBO EXHAUST MANIFOLD - SPORTLINE | eBay

couls anyone give me any advice on blanking the holes off once i have removed the flaps need to get this right as i dont want to be removing it again thanks

hi there can anybody help me i am removing the inlet manifold the only thing that i can see that is stopping it coming out is the dipstick tube i have undone the bolt but cannot pull it out anyone got any ideas thanks

Hey guys, Has anyone one here ever fitted or had experience with fitting a Stainless steel performance type Exhaust manifold to either of the N/A M111 engines like the 180 or 200? Have always found it to be a worthwhile mod in the past either freeing up some power or at least providing...

hi could any body help me with the removal of the inlet manifold i have so far removed fuel rail, power steering resovoir fuel filter and housing cradle that sits on top of manifold and some sort of silver box that contained coolant have removed all bolts from manifold could any one please tell...

Theres a chance someone might have one :D

Guys - just wanted to share some photos as some might find them interesting/useful : Downpipe bolts (what was left) : This is where mine was cracked giving a 'blowing gasket' type sound. Turns out the manifold is stainless with cast downpipe connector and top flange. The repair job...