seal

My A200 is a pre-facelift 169 coupe, so suffers from the known wobbly weld rust problem. Tried to get Mercedes to take care of that under their 30-yr rust warranty, but no luck, despite the full MBSH, and it's being on Service Care plan. So, what are my options - how to remedy this...

Hi all Just noticed my 2008 slk is dripping on the edge window seals. So, if you are in the car, looking at window, the seal on the corners that look like flaps gather some water and drip when raining. I noticed it today, flick the flaps (so to speak) and only a bit of water there

While driving my C220 W204 a warning came up saying "check engine oil when next refuelling". Because the engine started to sound rough I drove the four miles to the main dealer very gently. The engine did not overheat nor was there a warning of low oil pressure. However, the engine required a...

can any one tell me how to fit the front rubber seal on 107 hard top please

Hi guys, new to the forum so be kind. My trust C220 is making me lose what little hair I have. Long story here goes : I have had a leaky injector for a while, last week I removed it and replaced the seal, all good, no leaks off I went. Tuesday this week was out and about and noticed the...

The seal which sits between the glass and body has over the years worn away. It has like a velvet finish to the seal. Does anyone have a WIS guide on how to replace this seal?

Hi, I recently acquired a panoramic roof. The front seal is not attached correctly (45 in diagram) and I want to re attach it - is there a diy available for this? I have WIS/ASRA which has various diys but not for this front seal I don't think. I have been searching the internet for a while...

So I bought this to try on a few customers cars ,I don't know what's wrong but it doesn't bead up , feels very smooth on the paint . I used the C2 crystal with great results Puzzled by its performance !!!

As per title. (Warning to the squeamish - language gets a bit FFFruity. But, ****, they get the job done!) https://www.youtube.com/watch?v=zFmC66YU6zI

Hey! I'm new to the forum and have been following advice on other post but I'm still struggling massively. I brought an ML270 last month, with the an injector bolt snapped, and the injector half ejected from the head. So I drilled out the bolt as far as I could, tapped a new thread etc etc...

The cable snapped on my window so i've replaced it, however now the window doesn't seal when its shut. At first the window hit my b pillar so we loosened the clamps that hold the glass in place and slid the window over a bit and it now clears the b. Pillar and we thought we had it sorted but...

Hi all, once again the first injector is blowing through the seal, in the past 2 years this will be the 3rd time of having to get it fixed, is this normal? I have read somewhere that I can use a different copper seal than the merc one that is slightly thicker, think it was a honda washer, is...

can anyone tell me how to fit front rubber seal to 107 hard top

Hi - Posted this over on pistonheads but thought I would try for thoughts here too! Hope that is ok - tried a quick search here but didn't see anything. Have just had my large B service done at an Indy (DDR surrey, very friendly, good value, have STAR, good service and a quality result so...

Hi all hope your all ok and hope your MB are all behaving for you. Just an update as last Sunday I had a no 2 injector seal give up on my ML270 it's got a 3 month warranty so at 715 this morning I made a 57 mile one way trip to Llanwrtyd wells just past Builth wells to get it done and fair play...

Hi Guys what is the best way to fit front rubber seal to 107 hard top, thanks for any help:thumb:

can anyone help does a 107 hard top have a front rubber seal there is a channel on the top so it looks like one is missing. if so where can i get one, thanks for any help, Alan

Any body help me with a sunroof seal for my W124 Coupe..:confused:

Hello fellow members&a happy xmas to you all. I have a 55 plate clk 270 cdi & i heard a ticking / hissing noise coming from the top of the engine so i poured soapy water along where the injectors are & the 2nd injector from the front of the car was blowing. Will these be the injector seal ...

Hello All Just wondering where you guys buy rubber seals for your car's from? I'm after a new bonnet (Hood) seal Cheers in advance Dan