Vito 113 fault codes?

[ronnie63]

Had EML come on but no limp mode and drove normally. Had codes read and had scrolls of stored faults! Where to start, clearing them has put the light out, here is what I have

 

[ronnie63]

Anyone any pointers on any of these please?

Thanks Ronnie

 

[ronnie63]

EML back on, anyone have any advice at all?

Thanks Ronnie

 

[m80]

Fast thought it looks like your Lambda has issue.
But I wouldn't discount electrical connections being unreliable.

More info, age of Vito, which engine, it looks like you have a DPF?

Most like you will be needing an Indie to work through it.

 

[ronnie63]

Fast thought it looks like your Lambda has issue.
But I wouldn't discount electrical connections being unreliable.

More info, age of Vito, which engine, it looks like you have a DPF?

Most like you will be needing an Indie to work through it.

Thanks for the reply, it's a vito 113 cdi OM651 with 185k.

I had it in the garage recently with a water leak, the fuel filter housing was replaced. that garage (indie) read the codes I forget the number but his came up with charge flap bank 1 something?

The codes above were read at National Tyres and reset but EML stayed on after a cold start a few days later.

When the water leak was fixed EML also reset but stayed on after a cold start a few days later, he rekons sticky swirl flap?

Thanks Ronnie

 

[m80]

I'm not familiar with the 651, but I would be surprised if the swirl flaps were related to your oxygen sensor faults.

I would find a Merc specialist (Indie), you might save a lot of effort and wasted guess work.

 

[ronnie63]

I'm not familiar with the 651, but I would be surprised if the swirl flaps were related to your oxygen sensor faults.

I would find a Merc specialist (Indie), you might save a lot of effort and wasted guess work.

Thanks, I struggled before to find one in the Dundee area but will have another look

Ronnie

 

[ronnie63]

Just an update! had the codes read again today the top one P200A07 charge movement flap was not present the first time the EML came on!

I had the van in getting the fuel filter housing replaced as it had a leak, as this sits above the intake manifold I'm wondering if something has been disturbed to cause this new code? I assume charge flap is swirl flap?

Not sure how to tackle this? anyone any ideas?

Pic of new readout

Thanks Ronnie

 

[Gunnerkev]

Hi Ronnie I have a vito that stores a similar charge movement flap code to yours Just mine says the adaptation or adjustment is incorrect or the emergency position was not reached. I haven't investigated mine as its not causing any issues but code is there everytime I hook up the fault code reader. it could be the fact yours has a mechanical failure thats brought the EML on but mine also had the sensor problem on the cat and that will definitely put the EML on

 

[ronnie63]

Hi Ronnie I have a vito that stores a similar charge movement flap code to yours Just mine says the adaptation or adjustment is incorrect or the emergency position was not reached. I haven't investigated mine as its not causing any issues but code is there everytime I hook up the fault code reader. it could be the fact yours has a mechanical failure thats brought the EML on but mine also had the sensor problem on the cat and that will definitely put the EML on

Hi Kev, thanks for that, was your sensor problem resolved by replacing it? pre cat nearest manifold?
Thanks Ronnie

 

[IanHGC]

Hi Ronnie. I am having the same problem with my Vito as what you are experiencing. May I ask if you did managed to find the root cause for your problem experienced on your Vito. Is the vehicle now sorted and running well with no error codes stored. I am interested as to what you found to be the cause.

Thanks
Ian

 

[BTB 500]

Hi Ronnie. I am having the same problem with my Vito as what you are experiencing. May I ask if you did managed to find the root cause for your problem experienced on your Vito. Is the vehicle now sorted and running well with no error codes stored. I am interested as to what you found to be the cause.

Thanks
Ian

Hi Ian

I wouldn't hold your breath for a reply ... he's not used this site for almost 3 years:



Bumping the thread like this may get you some suggestions though. Fingers crossed!

 

[Oleks1992]

Just an update! had the codes read again today the top one P200A07 charge movement flap was not present the first time the EML came on!

I had the van in getting the fuel filter housing replaced as it had a leak, as this sits above the intake manifold I'm wondering if something has been disturbed to cause this new code? I assume charge flap is swirl flap?

Not sure how to tackle this? anyone any ideas?

Pic of new readout

Thanks Ronnie

View attachment 90482

If it's had fuel filter housing done check the metal cap with a round ball end of it.
It's part of intake shut off motor right next to fuel filter housing. I've seen lots of mb " specialists" crush it when replacing the housing and this traps the motor