Changing the Gear selector unit

Gary Beale

New Member
Joined
Mar 13, 2017
Messages
43
Location
Preston UK
Car
C200 Sport Estate 2012 Diesel Auto
Hi All
I have had the age old issue with the above and have decided to replace the unit (the car was in park and even though I did the old press the yellow manual button to free off the selector, I could not engage a gear). I called the RAC and he said that it was a torque converter fault??? Upon further investigation, it seems that it is the Shifter selector unit. I have removed the unit and wish to buy a used one from EBAY. My question is, does this new unit have to be "Coded" to the car. Thanks for any help or advice here.
 
The unit for my 2005 CLK did not need to be coded.
In fact, the unit turned out not be be defective at all. The optical position sensors had either drifted or solder joints had gone dry. A re-solder then adjustment using the slotted screws on the black optical module & it was right as rain.
I presume that yours is the same as mine - gear lever projects below the car & works the gear box mechanically via a lever as well as electrically. If so, then be careful re-connecting it. It's easy to not get the big clip on properly & it falls off on the test drive ...
Ian.
 
Hi All
I have had the age old issue with the above and have decided to replace the unit (the car was in park and even though I did the old press the yellow manual button to free off the selector, I could not engage a gear). I called the RAC and he said that it was a torque converter fault??? Upon further investigation, it seems that it is the Shifter selector unit. I have removed the unit and wish to buy a used one from EBAY. My question is, does this new unit have to be "Coded" to the car. Thanks for any help or advice here.
If you get stuck, speak to Steven at CVM on Pitman Way near Asda - MB trained and all round good guy!
 
The unit for my 2005 CLK did not need to be coded.
In fact, the unit turned out not be be defective at all. The optical position sensors had either drifted or solder joints had gone dry. A re-solder then adjustment using the slotted screws on the black optical module & it was right as rain.
I presume that yours is the same as mine - gear lever projects below the car & works the gear box mechanically via a lever as well as electrically. If so, then be careful re-connecting it. It's easy to not get the big clip on properly & it falls off on the test drive ...
Ian.
Hi
The linkage rod has become unconnected from the gearbox end during the removal process. Can you please supply more info as to where and how I can attempt your fix. Thanks
 
The linkage rod has become unconnected from the gearbox end during the removal process. Can you please supply more info as to where and how I can attempt your fix.

I presume that your gear selector module looks something like the image below. To re-attach it to the gearbox control rod, you should have a Clevis pin and flat clip that goes through the hole in the bottom of the lever and the hole in the gearbox control rod. I found it easiest to connect them from the underside of the car; however, if you have small, agile hands you may be able to do it by reaching down from the passenger compartment. Ensure that the flat clip has fully engaged in the groove in the Clevis pin, or it will all come undone.
Bolt the selector unit back into place, but don't tighten the bolts. Check that the new unit correctly registers 'P', 'N', 'R', 'D' on the dash as the lever is moved through the different positions. If necessary, slide the selector unit back and forth slightly in the elongated bolt holes to get the correct registration before tightening the bolts.

Ian.

Gear_selector.jpg
 
Hi All
Thanks for the replies. The fix was a very simple one. I removed the unit (although I did not need to), and replaced the clip at the gearbox end. I then doused the contacts on the selector unit with contact cleaner and took a chance on refitting it. BINGO! All is good. I suggest if anyone has this issue to spray the contacts first before removing the unit. This is a 30 minute job start to finish.
 

Users who are viewing this thread

Back
Top Bottom