Search results

Hi guys, Been a while since i ran Xentry on the old faithful Sprinter. Current have a 0.7a parasitic drain, so thought i'd hook up my PART_D to see if there was anything that may help pinpoint the draw. Amongst other things ( DPF related ) I have the following error : Error code 9020 - (OCP...

I will try to check the wiring. Do you know if the metal rings on screw holes of the yaw sensor are meant to be grounded to the chassis? Reason i ask is, my floor of van has been modded and carpeted throughout, so neither the screws nor metal rings in sensor screw holes touch any metal of...

I am happy to report i got the pins out!! :bannana: On the side of the connector is a barrier that needs to be slid out about 1mm. Once it is out enough you hear a click, you can then use your tool of choice either side from the top end and engage the little prongs, Quite some force was...

Hi Dec, That is one awesome post, i cant believe i didnt find it! Cheers for that, my adventure continues tomorrow when i have some daylight :) Cheers. Mat

heres the pic :)

Hi guys, Thanks so much for your response/s, and sorry i didn't take picture of the other side of the pins. They are female pins not like the EDAC pin unfortunately, i will try and take a pic in a minute. I have tried a simple 2 pronged tool, but it is not budging, i am thinking there...

Hi BlackC55 I did the live data tests i could see, including road test. Everything came back as good. Prior to doing these tests i did however pump up the rear end tyres, they were 25% out form the front! Do you think that this could cause this kind of problem, or is it just a...

Hi guys, I have a module connector for the paramterisable module, i have one cable come loose and one exposing copper, i need to remove these 2 terminals to repair, i have spent well over 2 hours trying to remove just one of them, to no avail :( I have tried prising the little clip thing...

Hi BlackC55 Thanks for the suggestion, how do i go about looking at the live data, i am sorry i am totally new to this STAR thing, and i dont seem to see an option for live data or any specific test for the yaw rate sensor specifically. Cheers in advance. Mat.

Hi guys, I have a 2008 Auto Sprinter 209 CDI, which is having some issues, it is a long story but to cut it short..... Last summer i went travelling Eastern Europe, whilst in Albania ( 40 degrees! ) i had a major auto gear malfunction. It turns out the wiring was melted and shorting as it was...

Hi guys, I am looking to replace my front discs and pads on my vito 110cdi Mk1 - I am wandering which caliper type i need to be purchasing for. From what i have read there are 2 types of caliper for this so not sure which pads i need. Is there a simple way to tell the difference by looking at...

Heya, Mine has done 136k I managed to get the injectors out yesterday using the cheap Nielson puller kit off ebay ( £25 ) did the job a treat, i now have them been cleaned and tested, will know the results later on :) Will post updates as soon as i know :)

Heh Mersum1ies, The engine has cooled now, i am soaking in carb cleaner and diesel to try and help loosen the injectors. I Might be best getting one of these tools, but im gonna spend a little more time before i do :) To get the engine hot again i need to put new bolts in which is a pain in...

Woohoooo :0 Got the 2 bolts out just now, and i must say they come out very easily - i was amazed! Unfortunately the injectors themselves do not budge, any advice on how to pr/wiggle these out? without damaging the injectors or the head? :)

Haha, well its Dryish lol - only a roof, but yer it is a big help! I have looked at the bolts on the assembly, but i don't see how i can move it backwards, and pull it in at the same time. Maybe i just need a to have a mess :)

Hi guys, The sliding door on my van is completely out of line. The rear of the door when closed doesn't pull in and there is a large spacing from the body of the van and rear of door, as shown below. The closest edge of the sliding door ( the side that meets with the passenger...

Yer my heater knob is not fully functional either, another job :) Let me know how you get on. M

I have finally got the blower working - my steps of diagnosis as below - for anyone with the same problem :) Checked main heater fuse f7c ( under the seat ) : all good. Removed blower from under passenger side dash. tested voltage to the connector : 0v ( should be reading something about 14v...

Cheers Pawnie :)

Lol - seems we cant have it all eh :) Thanks for the offer well appreciated - im in the West Midlands - Dudley way, so a bit of a trek :) I have a multimeter, just i dont know what to do with it lol - only had it a few days. I tried to get something from the cable socket that goes into...