om606

Hi, Does anyone know how to remove the clear pipes so I can replace the O rights? It looks like a white plastic tab to be pulled but before I snap any off I would like to check. OM606 3 litre turbo. Getting air in the tube :-( Cheers Martin

Hello – can anyone help me with a problem on my newly acquired 1994 W124 300E diesel? The problem is that the glow plug light on the dash does not come on until 30 seconds or so after the ignition has been switched on (and at the same time you hear the “clunk” as the relay kicks in). The car had...

Anyone got this?

Due to changes in circumstances (off work due to a badly shattered collarbone) I'm having to sell one of the vehicles on the drive! I initially bought the car at a time when my other vehicle had supposedly sold yet that fell through, and then due to my accident, I ended up with them both...

car in limp mode (or gimp mode as my mrs calls it) :( no turbo try to erase code - comes back even without starting the engine. Checked software still erases codes on other 'faults' - works fine. Swapped pressure sensor for known good one off my w202 (same part number) removed the...

I have posted about this before but the problem has returned. I have a cold to warm rough idle problem that disappears once the engine is hot. The rough idling feels like it's only running on 4 or 5 pots. Once above 1000 rpm it's smooth running on all 6 and pulls as well as a 300 non turbo will...

Hi all, Having a hard time deciding here, obviously I'm looking for a 190D, C-class or an E class older or newer with one of the above engines. It has to be an auto too. I've kind of decided on the OM605, but is it worth looking at the OM604 2.2CDI in the C classes or even the 3.0DT or...

Lusting after a C140 again - the coupe W140 from the 90's - but not lusting after the fuel bills. I run my cars on veg oil at minimal cost - so having a C140 running on veg would be my ideal car. Physically, I know the OM606 will fit - its smaller than any of the engines offered in the...

Hi I am new and need some help. I hope this is the correct way of starting a new post I am fitting a OM 606 962 turbo engine in a boat and I need to know a few things. 1 what car can I get a manual solid flywheel from to fit this engine. 2 I am fitting a OM603 N/A mechanical IP what mods can...

I raised this subject last year http://www.mbclub.co.uk/forums/engine/102155-e300-diesel-intermittent-rough-idle.html Now I have a problem similar to that on another car but only when it's nose down or after coming to a halt level or nose down. When it's started nose up it's lovely and smooth...

Hi, I'm looking for om606.962 turbo engine connecting rods. anaz-123([at])hotmail.com

As the title suggests, there is air in the fuel lines of my om606-equipped w124 (E300 Diesel T-Model, 124.191). I have researched this as much as I can and just need a few pointers. I can see bubbles in all of the clear plastic tubes, including the tube that leads from the fuel heat exchanger to...

I need to replace the noisy and knackered shock absorber strut and possibly and likely the idler but need to get the belt off first. Can anyone tell me the procedure to do this, ie firstly how do you remove the belt? Many thanks.

I have decided to update my car and so am selling my beloved W124 estate. See here Mercedes 1995 E300D W124 Auto , Mercedes Benz E Class in Bristol | Trade-It

how the heck do you get this off, the 15 or so hex bolts to the block come out easy, but i cannot see how to detatch it from the pipework? is there a particular area i should be looking for, or is it just a case of work blind?

Ok guys, following on from the http://www.mbclub.co.uk/forums/engine/121683-w124-0m606-flywheel-sensor.html thread, today I set about the gearbox swap. It's not finished yet but hopefully will be driving again by tomorrow night. Progress so far today has been the removal of the autobox, tourqe...

Hi, wonder if anyone can help. I have glow plug issues and was planning to take the manifold off over Christmas and do what's necessary, up until last Saturday the car would start after a bit of cranking and smoke and after 10 secs or so all well. However, on Monday night after the car had been...

Hi guy's, I have been thinking of converting my s124 to a manual gearbox. I have most of the part's laying about, however I have been told that the om606 in my car has a flywheel sensor. As the car runs a mechanical injection pump, I am curious as to why it needs to know the position of the...

om 606 engine om606 head om603 inj pump x 2 thanks

om606 engine bad starting problem. after leaving stud for a long time the engine spins fast on the starter. as if it had lost compression .then after a bit it starts to sound normal and then it fires up. after that it is ok until i levee it stud again ? help