m117

Has anyone fitted the above to a UK market car? Worthwhile? What happens to the EGR valve and associated pipework? Cheers

Good Afternoon Guys and Girls, As the title suggests, I'm wanting to do an engine rebuild on the above engine. Purely because my valve stem oil seals need renewing and with mileage being 158K, the timing chain, tensioner etc could do with renewing. I might aswell do a top end rebuild. Any...

Long shot but anybody know of one? Bare without ancillaries is fine but needs to be in good order otherwise. Cheers

Hello all, Anyone out there, got a Cylinder Head/Block drilling jig for timesert thread installation, on an M117 for sale or hire? Or knows someone who does this service, as in, uses Timesert not Helicoil, knows about the counterbore at thread openings, and that some of the threads are not...

I've had an oil leak on the front of the engine since I bought it 3 1/2 years ago but it's never bothered me as it isn't serious.... Hoever I'm now moving on to my next job of tidying up the rest of the engine bay so am thinking it's time to get it sorted. It's from the top somewhere - couple...

HI all I want to treat the C126 (1986 5.0) to a new set of leads and plugs, but I'm unsure re resistor Vs non resistor plugs and resistance in the leads. From what I've read the original leads would have had significant resistance built in, so were supposed to be used with non-resistor...

Odd request but I need a dead (a working one would be a waste as it's to be broken) V8, ideally a M117 or a later one will do. I can't pay mega money, hence not really after a nice one but will collect with cash and give you better than the scrap man :) Please PM me if you have an old and dead...

Odd request but I need a dead (a working one would be a waste as it's to be broken) V8, ideally a M117 or a later one will do. I can't pay mega money, hence not really after a nice one but will collect with cash and give you better than the scrap man :) Please PM me if you have an old and dead...

Hi I'm looking looking at buying a 560 SEC and just have a few questions regarding the engine change over. One car i'm looking at is a 1988/89 F reg when i've compared the engine to a 1990 model G reg theres noticeable differences in some components and layout under the bonnet. I presume...

Hi, I have a Euro 500sec 1984. It is getting a bit smokey but not too bad, just a cloud on hard acceleration. I have done a search initially on a 560 transplant but not comes up specific to my Gen 2 to Gen 1 requirements. I would like to keep the car as authentic as possible but definately...

Since Niks spoiled the surprise :doh: I might as well tell you chaps a bit more of what I been up too Been thinking about for some time,years to be more precised :o The plan was to get an estate and go ala Hammer :D So the search began for an early S124 with a good spec,and I mean...

Hello. Looking for a non-USA, non-airpump vacuum diagram for an early M117 5L engine. Circa 1980/1 - 117 960 Any assistance would be greatly appreciated, thank you.

Hi, Does anyone know where i might be able to source the few tools unique to the M117 engine at a decent price. Used would be preferred. Looking for the following; Pin puller for timing chain guide rails. Test Gauge for hydraulic compensating elements. (measures the height of the...

Hi, Does anyone know where i might be able to source the few tools unique to the M117 engine at a decent price. Used would be preferred. Looking for the following; Pin puller for timing chain guide rails. Test Gauge for hydraulic compensating elements. (measures the height of the...

Anyone familiar with these M117 camshafts, cast GTS55?

Hi all, Can anyone help with the conrod and crankshaft part numbers for an m119.960 (5.0) and an m117.968 (5.6)? Ta in advance.

Shame on the spec though Mercedes W124 E320 Mopf Umbau auf 560 V8!!!300PS !!!Perlmuttweiß!!!Ansehen!!! | eBay

Hello there, I recently picked up an early M117 5.0 DOHC AMG engine. :rock: Most everything is there but it is missing a few bits... Any suggestions on locating valves, springs, cups, retainers and two cam end cap covers would be much appreciated. Also, I have the German version of 73 page...

As title says, will the 722.320 4 sp auto trans bolt to the M117 engine. Car in question is an 80's 500 SEC

Guys I have a 560 sel engine, gearbox, loom and ecu's from a car I scraped long ago. My original intension was to swap this into a w124, but I seem to be sticking with improving the inline 6 so it needs to go. My question is, how do I tell if I have the standard 5.6 with 250ish bhp, or the...