Hi
Does anyone know how to test these? its coming up on the diagnostic but would like to test before I fork out for something I may not need
Camshaft position sensor (CPS)
Thanks in advance
I believe no AWD will be offered like the E63 models but the new C63 sure sounds and looks very fast.
The prices of the current C63 cars have been very stable over the years, I wonder if this new model comes out it will drive the old gen prices down. A clean C63 in the low to mid 30K US range...
Hi, I am test driving a late 57 (reg 08) 200K CLK Sport Convertible today. It'll be my first MB if I buy. It's a lot of money but then it's from a main dealer with all the usual stuff, top warranty, new MOT, very nice car of course.
Any advice very much appreciated. I'm in two minds re the...
After a demonstration of the Terra Clean EGR Tool I managed to swipe a box of these additives to test.
Anyone else tried this yet ?
http://www.youtube.com/watch?v=b2yYFxF39xw#t=28
I'm just testing the water as I would like the new Biturbo E63 BUT I am willing to hold on to my Current E63 if it doesn't sell as I'v spent alot of time and effort on it and it's exactly how I want it. So I'm not desperate but thought I'd test it here to see if there was any interest in...
Hey guys,
Off the back off our A45 tuning program we have now developed a plug and play tuning solution for the new 63 Bi-turbo engines...
Although gains won't be quite as much as a full remap initial testing gains have been around 70-80 bhp and 70-80Nm.
We are looking for a UK customer...
What does this mean now , we cant remove DPFs. it is becoming a requirement by VOSA to test your DPF on an MOT after Feb 2014
URL]https://www.gov.uk/government/news/new-rules-for-mot-to-test-for-diesel-particulate-filter[/URL]
Does anyone have a guide or wiring diagrams for the seatbelt presenters?
mine does not work on the drivers side (no response and in closed position), ive taken off the cover and dont know what the resistance should measure on the motor or know what the wires are.
ive googled and read many...
We are pleased to announce our long tube headers for C63 have arrived and we will be fitting them very soon....!
Gains should be significant....and yes these will fit RHD...
Hi all just thought we would keep you upto date with a few things we are upto.
Firstly we have now completed the final design for and fitted our electronic valves into the C63 Dual mode exhaust project. They work a treat and the difference is very noticeable between sport and race tones...
Folks
This is on my Pajero. When at idle, all the lights flicker on the dash as well as the sidelights etc.
I put a battery/alternator tester on the car and shows that the alternator is also flicking between good and fail (rapidly).
The alternator is still pushing out 14vdc (on a meter)
The...
I am Going to test the Oil sender on the 124 ( 220 petrol )
I think I have found it Is this it ?? and how do I unplug the connector Pull ??? ( dont want to break it ) I want to test the resistance to check the sender and sub a resistor to check the guage ) Thanks Boyd
Today I had my E500 dyno tested with 3 different ECU.
The Car E500 (previously owned by BING) 178kmi perfect working order.
ECU no1 pre 92 with full load enrichment (adapted to the engine as it has been driven for 200km)
ECU no2 post 92 without full load enrichment (not adapted as fitted 3...
Garage has finally replaced this. Dumb question - how do I check it is working without breaking into the car? :bannana:
Been done by a Ford garage as that is whom I bought car from. All looks OK, but call me a cynic......