Hi guys, I really could use some help in diagnosing a vibration issue I have on my vito. I bought it 4 months ago with a very lightly slipping clutch ( only slipped if you were hammering it up a hill in a high gear) so I had my local indy fit a new clutch, they said the flywheel had a small...
Hi I'm have a 1992 w124 200e manual and I think the clutch is starting to go so I was wondering are all the clutches and flywheels the same on all of the manual w124 or do they differ also are they a duel mass and if so does any one do a single mass conversation any help would be appreciated
Peter
Hi I'm have a 1992 w124 200e manual and I think the clutch is starting to go so I was wondering are all the clutches and flywheels the same on all of the manual w124 or do they differ also are they a duel mass and if so does any one do a single mass conversation any help would be appreciated
Peter
Hi. A week ago, my local garage replaced the dual mass flywheel with a solid flywheel whilst fitting a new clutch and slave cylinder in my 2003 W638 Vito van. It was in a bad way and they recommended going to a solid one.
THE PROBLEM: I collected the van, drove about 500m and it went into limp...
Hello all..
I'm a norwegian guy who has been working my a## off to get the starter out from my newly purchased A140, 98-mod...
See the attached image of the flywheel ring-gear.. Is this worn out?
I'm used to BMW's and have never been bothered with replacing starter motors so I'm a litte...
Morning all,
After a mere 140k miles, my clutch is starting to judder when hot (but doesn't slip) so I suspect that I will need a new DMF. As I have no history of this work ever being done I have to assume that it is original. Obviously no point in changing just the flywheel so I'll do the...
Hi,
Has anyone had to replace a flywheel to fix engine misfiring or stalling in a
WDB124022-2C- with engine M111.960 ? This particular flywheel has the 4 steel
tabs to trigger ignition via L5 and also one additional permanent magnet in one
of the tabs so the HFM management can identify when...
Hey all. Well 2 weeks after buying my dream van the clutch has started to slip and have now got the wallet burning job of swapping the clutch. The issue is I can get a conversion kit to change to a solid flywheel and clutch for 140 less than a dmf clutch and that is presuming the dmf isn't on...
Hi all,
in order to help out a fellow member, I'm trying to find a manual flywheel for the m103 engine. It is the early solid flywheel that we need, normaly found in a 2.6 190e.
If anyone can help please get in touch.:thumb:
Simon.
Hi there, i am looking at getting either a w124 or w201 as they seem to last quite well in nz.
I think the mid 70's mercs used a fluid flywheel in place of a torque converter and pulled away in second as first was too low except on hills or for towing. Do the latter versions use a fluid flywheel...
I know there are some seriously clever people on here that can help me....
I have a small project on the go that will yield me 270bhp @ the wheels from past fitment analysis from other customers.
So i've always known for instance my 911 is 320bhp, now where is that @? The flywheel? if so...
On this side of the pond I cannot find any answers, I'm doing a MB606 retro fit in a late model truck. Can Somebody in here help me find a single mass flywheel that will bolt up to a eight bolt 606 crankshaft and has 144 teeth.
Thanks Jay
Guys
Been reading most of the net regarding starter motor problems ie. earth straps, motor rebuild etc.
I read about lightly greasing the flywheel via an access panel in the bell housing - now, should I try this or just get a new starter and be done with it ?!
Thanks !
Whitey
Hi guy's, I have been thinking of converting my s124 to a manual gearbox. I have most of the part's laying about, however I have been told that the om606 in my car has a flywheel sensor.
As the car runs a mechanical injection pump, I am curious as to why it needs to know the position of the...
I have a c220 cdi 1999 which requires a new flywheel spigot bearing. Main dealer says bearing unavailable, buy complete flywheel. Can anyone please tell me if and where I can buy the bearing I need?
Many thanks
Beetcedes
Ok all you parts people :thumb: Looking for a flywheel for a 270Cdi I believe (if the original flywheel is telling the truth) the part number is :- A6110320147. Thank you in advance.