m271

Hi all new to this site need help. 2003 c180 coupe m271 engine I rebuilt new chain,head gasket, valves, etc started up first time purs like a kitten but smokes ( fuel ) on idle clear when you drive not head gasket no blockages. jugers a little bit in park but pulls great and clean when you drive...

Still have the problem with the wives 200K M271. I have had the head and done all the valves, new sprockets and chain etc and I get the p0010 code. I have had the cover off twice and the timing marks are 100% on both sprockets. open circuit, does anyone know where the wiring goes to check...

Hi guys happy new year too all! Hope you could help me with a strange problem, my car is a 2005 c200 kompressor with the m271 engine. My issue is when I drive the car when cold I get a bad knocking rotational noise but wouldn't say engine speed and only happens under load. Strange thing is the...

Hi I have searched around a bit but could not find anyone with the same issue that i am having. I drive a 2005 Merc C230K sports coupe with not quite 40,000 miles on the clock. A few weeks back it put up a lot of codes, misfire, running rich/lean which were cleared and I didnt write...

Hi everyone, Great forum which has been a great help with other issues I've had previously. Thought I'd take the plunge and get involved with a new problem I have which is locating where a squealing noise is coming from on my 2004 C180 1.8L Kompressor, M271 engine. I've added 3 videos to...

Hi All Thought people might like to know that there is a cheaper solution to the camshaft timing adjusting gears problem on the M271 engine than replacing with OEM gears at almost £500 per gear now. I specialize in repairing these engines and it was always a factor of cost to repair or...

Hi all. I have a 05 c180 which was running fine and then wouldnt start. Threw a inlet cam sensor fault and garage Replaced. Car still wouldnt start. Removed cam cover and cams are way out of timing. One cam is out by about 90 degrees. Worn teeth on cam gears and oil in loom. Is this...

Hi. Does anyone here know is the Recirculating Air Flap for the M111 (230Kompressor) and the M271 are compatible and interchangeable ? I need to change mine on the M111 and found that in the US, the M271 one runs for about US$290 only. Thanks

Engine shut off once started.Cannot idle.I need to wait for 5min to start back my car.What's the problem.Thx Lee

Photos or any help etc my chain jumped a tooth and I striped down to look just want to know how to time up and were adjuster etc is ty Carl Sent from my iPhone using MBClub UK

I am trying to remove the air filter box on my c180k but the vacuum line above the MAF will not budge. Is it as simple as it looks? Just squeeze the circular clip and pull but there is no movement and I am very reluctant to resort to brute force and ignorance just yet. Thanking you for any...

Hey folks, New to the forum so forgive any ignorance. I've been pulling my hair out for the past week and desperate for assistance. I bought a W203 C180k M271 and have ran it flawlessly for 6 months. My MAF has been unplugged (as is faulty) the entire time and gives me an extra...

As I intend to renew the timing chain om my C180 I have been trying to source the clamp that holds the chain against the sprockets whilst the old chain is being replaced by the new. I can get them from the USA but seem to be drawing a blank anywhere closer. :dk: I thought I had cracked it when I...

Apologies if this has been answered before but I could not find the correct search term to get an answer. My 203 has now done 98,000 miles so I intend to check the timing chain for signs of stretching. Does anyone have the dimensions of a new chain so I can compare it to mine and also the...

Hi. I have a 2003 w203 coupe c200 kompressor .the cam chain has jumped and bent the valves ,I can get a head from a 2008 car engin code 271956 would this fit ?

Hey people iv owned my CLC 180K almost a year now and fancy upping the power a bit (I don't want crazy figures more like 170-180 bhp) I know the clc200 make this power as standard but don't fancy selling mine to find a clc200 rather just keep mine at stock levels But if anyone has done it...

Please see video and let me know if it sounds normal cold start engine was started after being stood for two days in -1/0c weather http://youtu.be/MXX3Zm5fmoU (cold start) http://youtu.be/oGHGCx77qIs ( when engine warm) Clicking noise lasts for about a minute during cold start. When warm no...

Hello, anyoune ordered and using this performance kit? Is it ok? I am interested in this solution. What about fuel consuption. Is really fealable the power rise? What about noise? I am now using kleeman headers and cat but sometimes i have engine icon on instrument cluster. I need a really...

As some of you might know i get clicking noise when I start the engine on a cold start for around 20-30 seconds and then goes away but flawless when engine is warm. Here's the link to the video when then engine Mercedes c200k kompressor m271 engine noise - YouTube Does the engine...

Which oil do you use in your m271 engine and which one is recommend ? Been told mobil 1 0w 40 is too thin for m271 hence bit of clicking and clatter on cold starts as it leaks out of the tappet valves overnight. So when the engine is started in the morning the valves have to repressurise...