remove

Hi I hope someone can help me I damaged the star badge on the boot of my 2012 W212 eclass yesterday by rather stupidly reversing the car into a metal barrier . Fortunately, no part of the car was damaged except the star symbol on the boot lid! I will be off to the main dealer on Monday...

Hi all, I'm having major problems changing my diesel pump. The mechanic doing the work is trying to confirm what degree the timing should be before fitting the locking bolt. He is fairly sure it is 17 degrees. The other problem is the pump won't lock, there seems to be a break on the lower shaft...

I've had my car a few months now and I was hoping the lingering smell of smoke would have disappeared by now, unfortunately not. Any tips on getting rid of the smell? I presume it will be lingering mostly in the soft materials.

Hi guys. I wanted to check if my car had aux presided. I pulled back the door will, then went onto a pillar, removed the torx screw, but can't seem to remove these yellow clips which are really stobborn, and not sure if it's ok to use force to remove them or if there are certain ways I should...

Hello all. I thought it was about time someone did a write up on how to remove a stuck injector, re-cut the head face and re-seal. The car I am doing this on is an ML270CDI. Most of the rules apply to all CDI injectors. Make sure the engine is HOT. It will help. Firstly remove the engine...

Hello all. I thought it was about time someone did a write up on how to remove a stuck injector, re-cut the head face and re-seal. The car I am doing this on is an ML270CDI. Most of the rules apply to all CDI injectors. Make sure the engine is HOT. It will help. Firstly remove the engine...

Please excuse me if I post this question at the wrong forum and please point me to the right forum, thank you. I tried to remove the lower cover under the dashboard at the driver side of my 1994 MB C220 so that I can reach the brake switch, though I have unscrewed all the visible screws, I...

For quite a while now, i've had intermittent difficulty removing the fuel filer cap on my 210. I can always do it in the end but SWMBO sometimes has to go and find a strong man to help. The cap is basically very difficult to turn. Does anybody else experience this. Why does it happen?

e5MZcxZdZdw

Hi all I have a replacement part for the damaged gearstick cover on my CLK200 55 plate Kompressor, except im not sure how to remove and replace? Any ideas? See pic below in respect of the part im looking to sort. Cheers Neil

I have the keys to use to remove the climate control unit and cluster, but wanted advise where they are inserted to release them i.e. is it half way down the sides?

Hi Guys, My 203 wagon has what I think is the genuine dog guard (with the net and roller load cover) now I cannot for the life of me work out how to remove it, nor can I find any instructions. Appreciate this could be a really stupid Q but any pointers much appreciated! Thanks

How do I remove and install a new grill on a 2005 CLS W219?

I've always de-badged my cars and simply used fishing wire then a thumbnail to remove the glue left behind. But with my CLK either its typical Mercedes over-engineering or its because its nearly 12 years old but I can't shift the glue on the boot of the car! It's taken me hours just to...

Eventually I manage to remove heater control panel Found that pulling of the knobs you can get access to the lights How do you remove them and what is the replacement lights I tried pulling them with no success Many Thanks

hello everyone i have tried removing the parking sensor with no luck can some please guide me on how to remove it without breaking something, if possible without removing the whole bumper because i can see the sensor if i go under the rear bumper heres a picture of a similar sensor ,i am...

hello everyone i have tried removing the parking sensor with no luck can some please guide me on how to remove it without breaking something, if possible without removing the whole bumper because i can see the sensor if i go under the rear bumper heres a picture of a similar sensor ,i am...

hello everyone i have tried removing the parking sensor with no luck can some please guide me on how to remove it without breaking something, if possible without removing the whole bumper because i can see the sensor if i go under the rear bumper heres a picture of a similar sensor ,i am not...

my replacement c250td has a failed turbo - the actuator is siezed solid. So I thought I would nick the one off my old car. Cant undo the three nuts holding the turbo to the manifold, seized solid, cant get the nut splitter in there either. So I thought I would just take off the whole manifold...

Having replaced my broken speedo with a 'known-good' donor today, I'm still left with exactly the same problem - a speedo which doesn't work and which dances all over the gauge. With great difficulty I managed to remove the binnacle, insert the new speedo and replace it in the dash with the...