torque

Hi, Is the same torque required with aftermarket wheels, on Mercedes wheels on a CLK the torque is 110nm but this never seems tight enough to me. On Mercedes wheels the wheel bolts are radius but aftermarket wheels use tapered wheel bolts, so I wondered if the different shaped bolts for...

hello all, I wonder if anyone knows a 'roundabout' figure for a torque converter replaced on an R320 cdi. Mine is a little vibry........... I am Bristol based if that makes a difference? Cheers D

Hi Guys My w211 e220 has recently build a small problem in my case. At around 1500rpm it idles to pick up torque. I have to push the pedal a bit further for it to release it self and reach anything above 1500rpm. Can anyone advise me on this please.??

Hello All Anyone know a good place to order a torque converter for a 04 E55 AMG Mine needs changing according to TM Motors... Trying to weigh up cost of refurbing to getting new?? :dk: Regards M

Just renewed the seal from the block on the above pipe and putting new copper washers either side of the Oil Feed Banjo Dont want to overtighten or not tighten enough also dont want to dissemble Air Filter Box & Hoses to Tighten Up again. Anyone Know the Torque figure its a 13mm Banjo...

We had to check the results twice to make sure it was not a misread, those that have visited us will also know first hand 55K's don't tend to read as high as other dyno's. Great colour SL55 that was previously tuned by another company, I met the owner at a MBClub GTG and after a couple of...

Hi I'm looking for some help please. I have changed the transmission fluid on my 59 reg W639 Vito auto but can't find the torque setting for the drain plug and pan bolts. Is there someone who can tell me please?

:fail Sorry guys without knowing I posted this in the wrong sub forum sigh..., don't know how to move it, don't think I can? Hi Guys, So today I wanna put my new steering damper in my 1994 E280, it's a Sachs 280 999 (Super Touring) and I wonder what the torque specs are for tightening...

Can i ask for a little help . New water pump is in the car, and i am about to refit the pullys.I am short of one torque figure .This is the viscous fan assembly.The fan pully i removed to take the belt tensioner strut off. I now want to refit this item but without the settings i am held up...

Hi just about to replace the pully on the tensioner on my w124 260e the pully is worn on the face only .Removed the old one .Can you tell me where i can find torque settings for this pully .Only thing holding me up for 2 hours , as i have been looking for the figures. My Haynes Dandy as...

Hi,just been to the main dealers to get the gearbox checked, it went into limp mode which reset itself, it is also holding on to the gears, slow at changing up. I thought it needed a software update, our wrong can you be! Requires new Torque converter, luckily it's still just in warranty 1st...

My W126 500SEL has a small oil leak from one of the rocker covers. Before jumping to the conclusion that it needs a gasket I want to check the tightness of the bolts. Does anyone know the correct torque settings? Don't want to over tighten things.

Can someone point me in the right direction in my search of a document that contains torque values for high pressure fuel lines attached to the common rail and the cooler line bolt (at the far end of the rail)? Car is C270 CDI with the OM612 engine. Cheers!

MQm5BnhTBEQ

Hi all. Could you let me know the Torque settings for the following: Gearbox sump plug Gearbox sump retaining bolts. Cheers Sent from my iPhone using MBClub UK

Well, I seem to be having a little prob with my CLK. Actually, there are two of them, that bloody ESP/BAS light went on again, but that's a different problem. For now, lack of throttle response and torque. The car used to feel all right, pretty punchy even at part throttle, until i decided...

Hi. What the torque setting for the top ball joints on a e class 270 03 reg ???? Cheers Sent from my iPhone using MBClub UK

Had my SL55 back at MSL this week. New Mercedes brake discs and pads all round New air filters New plugs Custom exhaust incl. X pipe Awesome service and good food as always :D Met a couple of the forum guys there too.... good to see you chaps! Acid even rung me up to make sure I...

Hi All I have just had my exhaust mid section reverted back to stock, as I have now decided I want to go for headers and wanted to re-use my original secondary cats to save expense of sports cats etc.... So I now have for sale my stainless steel mid section, made and fitted for me by Imran of...

I bought an E250 estate (reg 60), which I have had for for months. I replaced the tyres with four new Hankook tyres (24545/17). I took the car to the main dealer for a first MOT (which passed). I subsequently spoke to the Service Manager and was surprised to be told that I would only get...