I have today been advised while having MOT that I have a very slight amount of play in a front wheel bearing.
Can I adjust the bearing by tightening the locknut and adding grease or is it a new whee bearing.
An help would be appreciated
I have today been advised while having MOT that I have a very slight amount of play in a front wheel bearing.
Can I adjust the bearing by tightening the lock nut and adding grease or is this a new wheel bearing.
Any assistance would be appreciated.
Front brake disc, pads and bearing wheel advisory on MOT.
On the last MOT(which was on 30.08) there is an advisory info which stated that:
002 Front brake disc worn,pitted or scored,but not seriously weakened (3.5.1i)
003 Offside front front wheel bearing has slight play (2.5.A.3c)...
I need a drive shaft centre support bearing for my ML270. I did a search on ebay and two UK suppliers offered this bearing at a decent price, both being German manufactured, or supposedly. On further investigation one was made in china, the second was of inferior quality, so both these are out...
Hi everyone ive a noisy rear wheel bearing and am going to tackle this but looking at buying another hub to swap the bearing out in so my car is off the road as shorter time ive got new back plates and brake shoes anyway the question is this
Are saloon rear hubs same as coupe rear hubs ...
Can anyone tell me how to adjust (if possible) the front wheel bearing on a 2002 c class coupe showed a bit of movement on the MOT but nothing excessive
My first post as a shiny new member!
I have recently bought a 06 C220 CDI for a road trip to Italy. It went really well, with four adults and luggage aboard, in 35 degrees, apart from a noise not unlike a diff whine when hot. This bothered me so when I got to Rome I had a local garage check the...
C219 / 2007 320CLS front hub grease seal is the ABS sensor ring. It must be re-fitted to give the correct air gap to the ABS sensor. Otherwise, the ABS light comes on along with EPS and cruise control switched off. I changed the ABS sensor and the brake switch so I hope this helps others to...
Hi guys,
Got some vibration around 50 mph on my sprinter 2007 (MWB) which I am presuming is the center bearing
Can any one tell me a good place to order one, searched around but the choices seem to be ebay which at the prices can't imagine them being up to much and MB dealer ship at around...
Chaps,
My C32 supercharger bearing is U/S, any ideas on a replacement and where to get one? or the eurocharged pulley instead?
What you think?
I have seen the bearing from tiawan for about 60 quid delivered, thats the NSK OEM one.
Thanks
john
Hi All,
For the Prop-shaft bearing replacement, does the whole shaft need to be taken away or just one section, the front or the rear need to be out?
Thank you.
Olivier
Hi, Whats the set up for the front wheel bearings on my C Class coupe.
Fitted new genuine but need the set up for the lock nut??
Is it just tight until the plays gone?
Do I loctite the hex bolt?
What about the rear seal, just flush?
Coming back to the UK in November to do a large extension for my brother.
It's a double height side extension and I have to remove the outside kitchen wall, the problem is that it's load bearing.
From my days in the building game we used strongboys for a solid outside wall and needles for a...
Hi,
Can anyone help me? I have a Jeep Grand Cherokee 2003 2.7 CRD the same engine as the ML270. While tightening the camshaft bearings up after some other work one of the shell half bearings snapped (can see a flaw). Unfortunately I cant buy just one shell but have to buy the lot at £500+. Is...
My wife's 55 plate B180 cdi auto (had it since April) was making strange noises, and has been diagnosed by my local indy as a front wheel bearing which needs replacing. This is rather dissapointing given the car is sub 25k miles.
Been quoted £270 ish to replace it. Does this sound about...
Hi,
What are the symptoms of these going bad? My car has been whining over the past few weeks and at first thought it was only between60-70 mph but no i can defo hear it at low speeds, I have popped it out of gear and it still whines, Its also stays contant at higher speeds but at lower i can...