cylinder

On this side of the pond I cannot find any answers, I'm doing a MB606 retro fit in a late model truck. Can Somebody in here help me find a single mass flywheel that will bolt up to a eight bolt 606 crankshaft and has 144 teeth. Thanks Jay

Hi guys, Recently my 2001 A-Class (W168) stopped running on all cylinders. I took the coil pack off and couldn't see anything seriously wrong, and the plugs looked quite OK. I've borrowed an OBDII reader (Sealey VS8700 - nifty little thing!) and it showed 4 codes, which I reset, and then I...

Guys, anyone breaking a sprinter or vito? I need a cylinder head for my van, I managed to strip the thread in one of the injector bolt holes.:wallbash: Mine is a 2001 sprinter 311 2.2 cdi, please pm me with what you have. Thanks in advance.:)

I have a misfire on 10 11 and 12, so I am going through the fault possibilities, the first being the pre-cat o2 sensor for the rear exhaust bank on that side which has definately gone. When I had problems with 1 2 and 3 I went through the coil pack (which was faulty) The plugs (which were a dire...

hi i have recently been experiencing a glow plug fault, when plugged in to diagnostic, no2 cylinder glow plug is showing faulty i was hoping someone would explain how the cylinders are numbered looking from front of car. regards boxer :confused:

Hi there W210 Diesel 3000 1999 Chassis # 202.225 Engine # 606.962 Its sad to report that I'm looking for a replacement brake master cylinder due to my own stupidity. As if I didn't have enough to do... Thanks ECP M&C

4 cylinder springs are GMAX lower 40 MM used but good condition 6 cylinder springs are P.I lower 40mm used but good condition either set (4 springs) £60 delivered

Hi all, Where can you recommend a competitive price company for a master cylinder for my ML?

spark plugs have changed, is it possible that ignition coil packet is broken? or is there only bad connection between sparkplug and coil? Car is MB CL600 year 2001

I wondered if some kind member could let me have the torque settings for the cylinder head bolts and also camshaft cradle bolts for a C200 M271 engine. Thanks in advance.

Mobilo guy came out and this was the code found by the star machine. The mb technician said that the fault was caused by oil dropping onto a sensor when my dad topped it up as he had spilled a bit. He cleaned it and cleared the light does this seem plauside? Also he said to me the m271 engine is...

On the MX5 forum there has been a real gem of a thread where the poster has documented his efforts to strip, re-engineer (port/polish) and rebuild a 4 cylinder 16v engine head. I hope there are a few 4-pot owners here who might appreciate reading it. You can either read the whole thread here...

Hi to all... Well i just bought a Star C3 with latest software Xentry and all is going fine in that matter. While i was diagnosing the car i checked injector coding, and to my suprise in the engine i have 4 injectors "code 2" and 1 injector "code 1" while in the DAS system i have coded 3...

Hello, guys I have left my car outside for 4 weeks while I was on holiday. When I get back and drive it, the acceleration feels not even and the engine check light is on after driving a while. The car behaves normally for about 20 minutes but after that, it shakes at idle mode and...

Hi, I wanted to know where the valve timing marks on the cylinder head of a SEC 500 88' M117.965. The TDC is located on the damper on the crank, which is not a problem, but I cannot find the valve timing markings on the left or right cylinder heads :dk:. The cylinder Heads are going for some...

I am losing brake fluid by the pint. I have looked underneath and can't see the leak but the steering box is soaked. No sign of a leak in the wheel well and the top is so pristine that it is even hard to imagine any corrosion so close. I'm just wondering if the master cylinder seal is...

another job to add to the list of things failing on the car, the brakes have now gone took it to the garage and he says that the master cylinder is creating a vacuum and pulling one of the calipers back he reckons it'll be close to £200 with parts and labour any idea how easy this is to...

HI, I know of someone who rebuilds the soft top hydraulic cylinders for the 129 better than new according to what I read on Benzworld forum, but he is in America. Is there a similar service somewhere in the U.K.? Regards thanks DARragh WDB129064...1999 SL320

Hi all, this is my first post on here after purchasing my 2005 c180k avantgarde 3 weeks ago. It was due a service when i bought it so being fairly competent with a spanner i thought i'd give it the works. It's only done 22k but i thought i'd treat it to the following. renewed oil and filter...

Hi all, changed the brake fluid in my w210 recently, the fluid that came out of the front nipples was dirty, the rears came out clear. Would this be a sign that the seals are starting to go in the master cylinder? The pedal feel was slightly spongy before, feels quite a bit better now.