injectors

hi wondering were is best place to get ml270 injectors,can you get aftermarket at decent prices ?.thanks :thumb:

Only had the car 6 months (11/2011) it has 27K miles on clock i have done 11K of them. Anyway got the car into MB to look at spare key as it looks like it needs recoding and they rang me to say they have given the once over whilst it was with them. They state the injectors are all "furred up"...

Hi, We have a 2003 W638 Vito, 112 with 9 seats and friendly name is the "venga Bus".... anyway... Always looked after serviced but does get used a lot as my daughter is part of a dance troop so spend many a weekend cruising the Motorways to and from venues all across the UK.... Venga is a...

would anyone know wat the parts number is for injectors in the e320cdi 2006 v6 ,

Can anyone point me in the right direction for a set of 4 fuel injectors for a 2001 CLK230K ? I tried a set of remanufactured ones from the US. Initially it solved my fuel consumption problem (down to 12.5 l / 100 km) but after 600km , fuel consumption went up again to 16.5l / 100 km. I...

Has anybody got any experience with these? Life expectancy etc. Rule of thumb is normally 80-100000 miles before changing them, does this apply to injectors in this type of engine? Any information greatly appreciated. Thanks Martin

Need advice! Very very smokey/sooty exhaust on my 02' E220 W211 tried injector cleaner all sorts of emission lowering fuel additives, new air filter, cleaned ERG & air flow meter still no luck. No problems starting, smoke not too bad when cold but when at operating temp say 1/2 idle for a...

Hi Guy’s This is one for the experts! or maybe not ? I have a ML 270 Cdi 2002 W163 When in icy weather I noticed it tacking a long tome to start up, sometimes as long as ten turns of the key. Once started it won't give this problem and will start on the button and tick over fine. I...

Can anyone reccomend the cheapest place to buy new injectors for a 220 CDI, I don't really want reconditioned ones, I know their normally an exchange part too so will have to give my old ones back, just wanted to see if there's somewhere that's better value before I go to Mercedes.

Is this possible on the v6 cdi? I am having, an intermittent hesitation on low rpm which clears up every now and then... its annoying when it happens so I am wondering if it is possible to have them stripped and cleaned? and if anyone in the NW does this? Have ran forte and its still...

Hi '92 300TD, om603 non-turbo. Fuel filters replaced a few thousand miles back Haven't driven the car recently, missus has been using it... she says it's a bit rough and smokes a bit on starting... Went out yesterday and it would barely start, much cranking got it going eventually...

Hi last year in November I bought a V Class 220 Ambiente the car as going fine but inside cabin was a terrible small of fumes. So I found out about the so called " black death" and I went to change the Injectors seals. This forum was good help just reading all the different topics about black...

Hi, I have a 2003 e270 cdi and it recently cut out on me, I took it to a local garage and they said one of the injectors was faulty. is this a commonn fault and any idea on costs to fix and can I use a recon part, as we were looking to change the car before Xmas and now this happened! sods law!

replacing seals this weekend and would like to replace injector wires and connectors, is this possible with a replacement loom just for the injectors?forgive my ignorance

98 E300 TD M606 turbo Think I have a blocked Injector......are the injectors easy to remove and are any specialist tools required. Many Thanks EMH

Hi Guys, The seal on injector 6 has been leaking and has left a black, hard glossy deposit around the top of the injector. I have managed to get the injector out and have cleaned the surrounding area. On inspection of the injector it would appear that the seat has become pitted. Does this mean...

Hello, I am looking for the Additional injector holder of the Turbo Techniques Twin Turbo KIT for the M103 and M104 engines. please PM me if you have one, or know of someone that have it, or if you seen it for sale somewhere. thank you.

The belt tensioner pulley on my recently purchased 1990 300td is out of alignment with the other pulleys. It sits further back towards the engine than it should, so the belt is off the front edge, and is wearing out the newly fitted belt. Any tips would be much appreciated! Also, the engine is...

Hi all, I have been advised to change the injectors in my 1992 300TD owing to it's mileage (240,000 miles) I have sourced the injectors and would like to carry out the work myself, is there anything I should watch out for or any tips and tricks? Thanks

I need 5 altogether... The bloke who's fitting the new nozzles and setting the pop pressures can't turn them around that quick, so I need another set I can give to him so the car isn't on stop! Many thanks