pressure

Can someone tell me the correct pressure for Viano w639 with 225/55/17 (front and rear), not run-flat tyres? I checked the plate at the fuel tank lid, but it only shows run-flat tyres.

We are looking at ordering a set of winter wheels and tyres for my wife's 2013 SLK. It currently has tyre pressure sensors fitting on the manufactures wheels. Would it cause any issues to fit other wheels without these sensors? Will it constantly give an error message? Thanks

I have for sale a high pressure fuel pump for sale from my accident damaged e220 estate..... offers welcome.

Hi all, I have a new DPF fitted but still in limp mode. i have had it checked again and the DPF Pressure Sensor is the issue. i have had a look on the internet to find out what this looks like and where its located. Can someone help please and would i be able to do this myself? Thanks Brent

Hi guys I know this has probably been done loads but the search option is not working on my phone and I have just returned to my car and all the tyres are down to 2.5 bar. I have a 2012 coupe with the 19" black multi spoke alloys! My question is what pressure should they be for normal driving...

Need To remove one of the pipes to the Petrol Fuel Injection Rail on the C240 (M112) I Know you can releive by loosening the filter Banjo band by starting with no fuel pump fuse But as the engine is as below and is not up on ramps is there a "proper" way with a more controlled and safer fuel...

Problem: Under hard acceleration the EML comes on and limp mode limits revs to about 2/3k. Car is S320 2007 with Brabus D6, Installed from new. 1st main dealer fitted three new injectors although admitted they were still within limits. No change. An independent changed fuel filter, stripped...

I have for sale a high pressure fuel pump off my written off 2009 estate excellent working condition.. £130 ono car had covered 87k

My '04 E55 estate is fitted with TPMS. It doesn't work, partly because there is only a sensor/transmitter on one wheel; the other three wheels have ordinary rubber valves fitted. HOWEVER... There are two possible types of system which could be fitted to the car, and even Terry at Wayne Gates...

2006 5 cyl turbo diesel, 416 sprinter van, does the system use an oil pressure sensor which will not allow the engine to start until some oil pressure has been built up?

Hi all. Does anyone know the location of the Title on a 2001, CLK 320. Regards Ray

I have read all threads about how to reset the tire pressure Warming system. I get the warning when I start the car. However, the tire inflation pressure monitor dialog to reset does not come up on my display whatever buttons I Press. I also had to adjust the clock and found a lot of info...

Hi all, I have just joined the forum in the hope someone may be able to help me out with a bit of technical data? I am after the expected fuel pressure value, at the rail, on a 2001 W168 A140. It would seem the value given in the Haynes manual is way off (errors can be common in their...

I was driving my W123 300d (non-ABS) on the A13 today and after about an hour of driving at 65+ mph, I experienced a sudden loss of brake assist/ boost. Here is all the information I have: The pedal depressed much further than usual repeatedly before any braking took place Pumping repeatedly...

Hey guys, I have a W204 c200 CDI. 2007 Can anyone help? Cut the story short. A/c wasn't working. Had it gassed and serviced and still wasn't working. Friend at Mercedes put it on Star and found out it is the refrigerant pressure sensor. Wheel nut shaped with thread one end and wire...

Hi can anyone recommend a budget pressure washer to use in conjunction with a water butt? I have a 240l Waterbutt and want to make good use. Will the water leave marks on my car or is rainwater better than the tap water (note we get hard water here) Also any recommendation for snow foam liquids?

Guys, I'm in the process of purchasing a direct mount (the fuel rail) fuel pressure gauge. I've opted for an Aeromotive which has a 1/8 NPT fitting. What I need is an adaptor to plumb into where the Schrader valve is on the rail, I think I'll need to screw out the valve itself before screwing...

Guys I recently had an issue of VERY violent "kangarooing" when I floored it, this caused an error code to be logged "Exhaust backpressure sensor ..............too low". I had the can in at the local Indy today, they said the exhaust back pressure sensor is in the top of the turbo. As...

Can someone tell me where to locate the oil pressure sender on a SL500 engine, I have what I think is the sender on the lower front left of engine (from the front) it has one electric connector on it, but the new ones I have looked at have 2, . Also where is the engine number Wal

Hi I have tyre pressure loss warning on my s211 e280 and was wondering what is required to add tyre pressure monitoring and will the latter enable the tyre pressures to be displayed? Thx Steel e