• The Forums are now open to new registrations, adverts are also being de-tuned.

inlet

  1. Danny DeVito

    Oil in my inlet manifold

    My own problem now is why is there so much oil in my manifold ? Dirty oily mucky coating in it and a puddle collects in the egr. I have cleaned the crank breather but its seems to be very ineffective at blocking the oil from being sucked out with the gases. If anyone knows of a solution to this ??
  2. S

    W203 C220 CDI Inlet Manifold Removal

    Hi All, I am in the process of removing the inlet manifold from my C220 CDI. I am following the haynes manual which is not too bad however I seem to have a wiring loom and the ATF dipstick tube passing through the hole in the middle of the manifold. The haynes manual isnt particularly...
  3. M

    C270 cdi inlet manifold wanted

    Hi looking for a inlet manifold for my c270 cdi 05 reg anyone got one please let me know
  4. M

    C270 cdi inlet manifold

    Hi took my car to local indi he wants £750 to repair manifold . I asked him if he would remove flaps but no Said you carnt do that ? WDM perry bar. Does anyone know who would remove the flaps . I have been told car will run ok with out them.
  5. M

    Inlet manifold c270 cdi help

    Hi can anyone recommend a good mechanic To take off my inlet manifold & remove the flaps I have a funny noise & oil leaking under it. In the Walsall area or Birmingham. Also what am I looking at in time it takes and cost anyone help please.
  6. K

    Wanted e200 inlet manifold

    Hi does any have a e200 W124 exhaust manifold, it's the late 1995 16 valve model. I'll collect from all over yorkshire, upto Durham, North Midlands and Lancs. I also need the heat shield.
  7. H

    w210, e270 cdi inlet manifold flaps remowal, PICTURES

    Hello mates! today i took apart my inlet manifold on my e270 cdi, w210. the car was in limphome with faultcode p1189. It was a little oil in the presurehoose, and the EGR was completly full with black sh*t! When i came to the inlet manifold i saw that only one rod was conected to the...
  8. C

    Inlet manifold servo protector For MB C, E, CLK, R, GLK,……V6 CDI 280 and 320;OM642

    This piece is placed in order to protect the inlet manifold servo. The inlet manifold servo is a well know breakdown in this kind of engines just only consult it on MB forums to confirm. The cause of this failure is the hot oil that falls down in the servo who rules the admission. This piece...
  9. M

    screenwash inlet pipe

    Hi all, as I am in progress of sorting out my poor fuel consumption problem, I am also working on something else in the engine. In the E280 CDI V6 engine, under the pollen filter, the screen wash liquid inlet pipe is visible. This pipe goes through the passenger side fender (body) into the...
  10. dokalj

    ML270 Leaking Inlet Manifold?

    Hi all, It was going to happen some day. I was checking the engine bay over and I think I can see oil running down the side of the engine block? More so, I think I can see it flows back towards the back of the engine. (A bit difficult to pick up on a camera) The car is currently driving...
  11. W

    inlet port shut off motor delete

    looking for the above post a think it was by Alex Crow it was for the ml270 either that or i want to know how to attach the resistor to the motor eletrical plug on the vehicle and where do you get the resistors thanks
  12. BlackC55

    V6 Diesel inlet port shut-off motor FIRE

    On a V6 diesel the inlet port motor caught fire. The white stuff is foam from the extinguisher. Very scary stuff as the flames were huge!!
  13. A

    inlet manifold blanking holes

    couls anyone give me any advice on blanking the holes off once i have removed the flaps need to get this right as i dont want to be removing it again thanks
  14. A

    inlet manifold removal (dipstick)

    hi there can anybody help me i am removing the inlet manifold the only thing that i can see that is stopping it coming out is the dipstick tube i have undone the bolt but cannot pull it out anyone got any ideas thanks
  15. A

    inlet manifold c220 cdi w203

    hi could any body help me with the removal of the inlet manifold i have so far removed fuel rail, power steering resovoir fuel filter and housing cradle that sits on top of manifold and some sort of silver box that contained coolant have removed all bolts from manifold could any one please tell...
  16. R

    om606 inlet manifold removal

    how the heck do you get this off, the 15 or so hex bolts to the block come out easy, but i cannot see how to detatch it from the pipework? is there a particular area i should be looking for, or is it just a case of work blind?
  17. J

    Air inlet pipe question (m271)

    Hi all, I have a question about the material pipe that goes from the airbox to the grille... Mine split and ended up dangling down In front of the belt. I have rang up a parts dealer and they said it will be £26.10 + vat and he's not sure if it just the material pipe or if it comes with the...
  18. R

    Inlet Manifolds CLK320

    Hello, I'd like to start a thread about CLK's and Limp mode. What causes your limp mode an how much it costs to fix. I'll start with my second limp mode (the first one I've had to pay for) Diagnosed as both inlet manifolds and an inlet manifold purge thingy ( i can't recall perhaps someone...
  19. ozzyboy

    c250 turbo diesel inlet sensor fault

    put this car on diagnostics today and it threw up inlet manifold sensor at fault. any ideas
  20. biturbo

    fuel injector oring fell into inlet manifold

    After using one of the those fuel injector cleaners redex i started to develop misfires and dog running. I've got the misfires on my sl60 after about 5mins of it being warmed up. Then it was running like a dog. felt like fueling problems and i thought might be all the gunge being unblocked from...
Back
Top Bottom