position

Vehicle - w210 E320 1998, 62500 miles. Around a week ago the car cut out at traffic lights and although it has been OK since I am wondering if it might be prudent to fit replacement Crank Position Sensor. I have a subscription to ALLDATA which indicates the MB part no. Is 003 153 95 28. I...

I have looked through a lot of forums on this but cannot find the answer. My headrests have gone to the upmost position and will now go back down. I am in France at present and now cannot open the hood as the headrests are locked. I have tried the reset, hold button for 20 seconds etc but...

Hi, Odd one this, upon driving the car today I appear to be approximately 20 miles further to the east than I actually am.......unfortunately somewhere in North Stifford I have tried turning off etc etc, even reset the Command/Radio but it still appears to be as good at map reading as my dear...

Hi All, Does anyone know the position of the yaw sensor on my '01 C270 CDi. Is says in the Haynes Manual that it's over the rear axle- I've had the rear seat out and can see nothing. In the boot there is a panel behind and beneath the back seat-the fixings look very secure although it may be...

Hi. I've not used the forum for a while, but I hope someone can help with this.... I'm trying to replace the crank position sensor in my E320CDi. It is a bit of a s*d to get at if you have big hands! I have eventually got the bolt out, but the sensor will not budge. I've tried by hand and...

My CPS has packed up on the C55 Estate and now trying to change it myself. I have looked at a load of posts, mostly on US forums, have 1/4 inch E8 socket and drive etc but cannot find the thing to change it! Can anyone help with where it is? Sticking my hand right up from underneath on the...

The most common complaint after front wheel alignment is the end position of the steering wheel this is a visual indication that 1: The workmanship was poor 2: The equipment is inadequate 3: Alignment was never the real problem 4: The manufactured cars axle is miss-aligned Nearly every...

I went on the mb website and looked at vacancys , I found 2 positions in Ipswich where I now reside . one was for a truck sales manager , the other was for a sales exec at the local dealership , the target set was 120 cars a year? in a team of 6 ? anyway sent off my c/v and covering letter , in...

Hello guys, I will take off the ABC rear valve on Sunday and replace the o-rings and clean it... as it is sticky. W215 (CL500, 2000model) What is the process of removing it, does it need for the system to be depressurised or because the rear wheels will be on the air there is no need to? ie...

Hi, can anyone advise me on how to change the crankshaft position sensor on my CLK 270 CDI on a 53 plate? I have read that it can be done from above on some models but I cannot see how this is possible on my CLK and wondered if it can be accessed from underneath?

Hi Anyone with star diag near the CH66 postal area please... Thanks

Hi All, I am going to re-fit the AMG badge (de-badged)..on my W211 E55, does anyone have a position template they can send me? Thanks. David.

Hi, As some of you maybe aware my AMG is at present in the bodyshop being resprayed, though the bodyshop are not at the stage of putting the badges back on yet I thought I would eliminate the need for measuring and guessing the badge position by asking if any kind soul could send me the WIS...

Hello All I have a 2000 E320 CDI which has the fault code c1140 steering position sensor fault. I have changed both the break light switch and the steering angle sensor with no joy. I have also performed the lock to lock resest several times again with no joy i am now out of ideas. The esp...

E55k Crank position sensor ..does anyone know the price and part number please? Many thanks.

Hi everybody I just bought this car - W210 E320cdi (2000year). I was quite happy with my new car and I was driving home. Suddenly at one roundabout the traction control light was flasfing and after that more than half of engine power was gone. I tried to change gears manually in +/- mode...

I just got myself a 260E and aside from a couple of little jobs required I'm delighted with it. However one unexpected problem has cropped up. I'm average height 5'10" and no matter how much adjusting I do with the seat I cannot see the upper half of the instrument panel. The speedo above about...

Hi. I just took out my CPS to clean and noticed there was a thick film of oil on it. Is this normal ? This is for a M111 230K Engine.

Okay Guys,I recently acquired this beautiful vintage watch - it ran fine,but the winding crown was a little stiff,so I contacted the seller in the US - whom agreed for the watch to be sent to a UK watch repairer and assessed and he would pay for the remedial work - rather than send back to the...

FRANKFURT -- Mercedes-Benz may regain its position as the world's second-largest manufacturer of luxury cars in 2015 after losing it to Audi last year, the German newspaper Handelsblatt reported, citing forecasts from the Center of Automotive Research at the university of Duisburg-Essen in...