torque

This event is held anually at an raf woodbridge in suffolk. Its purpose is to bring members of the piston heads forum together for a timed 1/4 mile and mile run against each other. Cars were at a plenty with the exotics of lambos/porsches to c63's a cls 55 m3's m5's tvr's etc. Everyone...

Ive entered the E55 into this this event which is all about brute power and pitting your car against a variety of super cars,sports cars and general every day cars. Basically the aim is to test your vehicles 0.60..... 0.100 and quarter mile times against other marques, for this purpose ive...

Hi all, I have an 84 w123 230e that I recently bought on ebay with a gearbox problem, It was was stuck in 1st then slipping and reverse, I bought another box which I duly fitted this weekend put in new fluid and filter and now have a very similar condition just without the slippage, I noticed...

What would be the correct torque for tightening the alloy wheel bolts on a W124 300TE Estate?

Hello, I drive a 1987 G-wagen, but my question is most likely to be answered here. The regular G engine 2.8L m110.994 failed. I purchased an m110.989 from 280SE/SEL 1981-1985 (185HP). I am looking for a power/torque chart or an actual dyno plot for this engine. I will appreciate any help.

Hello Does anybody know if it's possible to measure engine torque with the Star Diag system? The dealer I usually nag says it's not possible - maybe he's just telling me "go away and leave me in peace"! Peugeot and Mazda systems can do this and the relative compression can be measured with Star...

I was just reading the post on the Valeo radiator issue, i see that in the diagnosis they refer to disabling the torque convertor lock up clutch, my c230k (202) has the 722 6 transmission with tip shift, but does not appear to have a lock up clutch, is this correct i wonder? did some have it and...

Hi I'm looking for the Torque Specs for the Injectors on the OM606 engine (non turbo) I have read that 40Nm does the trick but isn't there a torque on torque off sequence that must be followed to seat the heat plate/washer corectly. Got a compession leak on a couple so while I'm at it I'm...

Folks My E55 seems to have a very fine leak from the Oil filter housing cap. I had mobile 0/40 put in a few weeks ago so i suspect that it could be the viscosity being too thin that's the problem. Im changing to a 10/40 but wanted to know whether using a torque wrench to tighten the housing...

I have just had my front suspension torque strut bushes replaced,:( to pass the mot . what is the quoted time for a dealer to replace car is a 2001 C 220 cdi

I've been reading up on a problem that seems to affect SLK32 and C32 AMG owners, although I suspect it affects other models too given the automatic gearbox is not unique to these models. People describe a jerk at 1500rpm when accelerating gently - many confuse it for an abrupt gear change...

Hi all Please see attached pdf document from WIS that explains why the drain plug in the torque convertors were removed. :devil: :devil: Cost saving:( As of 22.9.99 230k

Does anyone know what I should torque the wheel bolts on my 96 SL500 to? I am about to change the alloys and want to get this right. Thanks

Does anyone have the correct torque settings for the front lower balljoints, drop links and anti-roll bar bush holders. My WIS is playing up and I'm having difficulty finding anything. Weather is supposed to be good tomorrow so I plan to replace the parts then, along with a new set of...

Don't be. After hearing about how good modern diesels are with the ability to be chipped and people quoting huge torque figures I've discovered how disappointing they are. I've had a W211 '05 E320 CDI as a courtesy car for the last two weeks and it is horrible - noisy - terrible turbo lag and...

I'm looking for a decent torque wrench - mainly for wheel nuts to clean the alloys properly every month - any recommendations up to £50? Also a decent tyre pressure gauge.

Hi, Wonder if anyone can help as I contemplate a change of discs and pads. Car is E430 saloon 2000.(W210) 1. I know I have to use new caliper bolts, can they be bought from dealer or elsewhere cheaper? 2. What torque setting do they need to be done up to? (Front/Back) 3. They seem to...

Any tips on draining the torque converter on a 722.6 box. Its a 2001 W210 with no drain bolt on the converter, and yes I've looked and looked. I drained the pan last year and only got a few litres out. I'd like to do a bit better this year as I've got a whole bunch of expensive MB oil...

Hi, Does anyone know where to get original power and torque diagrams for MB cars. I am especially interested in one for my machine. Thanks.

I have a CLK 270CDI model Feb 03, 24000miles and the Torque Converter has had to be changed. Anyone out there who has experienced a similar problem?